Alto-Shaam Converge CMC-H2H

Other manuals for Alto-Shaam Converge CMC-H2H

Questions and Answers:

K
Kelly HesterSep 12, 2025
What to do if Alto-Shaam Commercial Food Equipment shows error codes?
- L
  Lawrence SinghSep 12, 2025
  If your Alto-Shaam Commercial Food Equipment is displaying error codes, try the following: First, power down the control using the ON/OFF button. If that doesn't work, cycle power to the oven by either unplugging it or setting the main disconnect switch OFF and then ON again. If the error persists after these steps, continue operating the oven, but be sure to contact Technical Service if the error reoccurs.
S
Stephanie WattsAug 22, 2025
What to do for sensor short (chamber sensor) in Alto-Shaam Oven?
- R
  rodriguezjacquelineAug 22, 2025
  If you're facing a sensor short with the chamber sensor in your Alto-Shaam oven, power down the control using the ON/OFF button. Cycle the power to the oven by unplugging it or setting the main disconnect switch OFF and then ON. If the error reoccurs, contact Technical Service.
R
Richard MoranAug 25, 2025
How to resolve sensor open error on Alto-Shaam Oven?
- S
  smithkellyAug 25, 2025
  If your Alto-Shaam oven displays a sensor open error, power down the control using the ON/OFF button. Then, cycle the power to the oven by either unplugging it or switching the main disconnect switch OFF and then ON. If the error continues to appear, proceed with oven operation, but contact Technical Service.
C
Catherine WoodAug 26, 2025
What to do if Alto-Shaam Converge CMC-H2H Commercial Food Equipment unit is under temperature?
- S
  Shawn WrightAug 27, 2025
  If your Alto-Shaam commercial food equipment is under temperature, try the following: 1. Check if the oven was preheated before loading the food. 2. Verify that the oven was not loaded with frozen food. 3. Press the high limit reset buttons. 4. Power down the control using the ON/OFF button, then turn the oven back ON and start a cook.
F
flowerslauraAug 28, 2025
Why is my Alto-Shaam Converge CMC-H2H electronics over temperature?
- A
  Amber LambertAug 28, 2025
  If the electronics in your Alto-Shaam commercial food equipment are over temperature, the following could be the reason: 1. Ensure the cooling fan(s) are working properly. 2. Check that the exhaust vents are clean and free of any obstructions. 3. Confirm that the oven clearances meet the required specifications. 4. Ambient temperature may be greater than 105°F (41°C). 5. Inspect the door gasket for any damage and ensure it creates a proper seal.
C
Christopher WagnerAug 30, 2025
What to do for a motor error on Alto-Shaam Converge CMC-H2H Commercial Food Equipment?
- M
  Mr. Cody DominguezAug 30, 2025
  If you are experiencing a motor error with your Alto-Shaam commercial food equipment, follow these steps: 1. Power down the control using the ON/OFF button. 2. Cycle power to the oven by either unplugging it or setting the main disconnect switch OFF and then ON. 3. Continue operating the oven. If the error occurs again, it is recommended to contact Technical Service.
J
jonessandraSep 18, 2025
What does sensor short mean for Alto-Shaam Commercial Food Equipment?
- S
  Scott KingSep 18, 2025
  A sensor short in your Alto-Shaam Commercial Food Equipment means that the control board has detected a short in either the chamber sensor or the probe within the chamber.
M
mark28Sep 13, 2025
What to do if my Alto-Shaam Commercial Food Equipment has cooling issues?
- S
  Spencer PetersonSep 14, 2025
  If you're experiencing cooling issues with your Alto-Shaam Commercial Food Equipment, consider the following: * Ensure that the cooling fan(s) are operating correctly. * Verify that the exhaust vents are clean and free of any obstructions. * Confirm that the oven clearances meet the required specifications. * Check if the ambient temperature is greater than 105°F (41°C). * Inspect the door gasket for any damage and ensure it provides a proper seal.
G
gibsonrussellSep 10, 2025
How to fix motor error on Alto-Shaam Oven?
- K
  Kimberly BallSep 10, 2025
  If you're experiencing a motor error with your Alto-Shaam oven, power down the control using the ON/OFF button. If that doesn't resolve the issue, try cycling the power to the oven by either unplugging it or setting the main disconnect switch OFF and then ON. If the error continues to occur, proceed with oven operation and contact Technical Service.
T
Thomas MilesSep 6, 2025
Why is my Alto-Shaam Oven electronics over temperature?
- E
  Erik SalinasSep 6, 2025
  If the electronics of your Alto-Shaam oven are overheating, ensure the cooling fans are working, the exhaust vents are clear, and the oven clearances meet requirements. Also, verify that the ambient temperature is not exceeding 105°F (41°C) and inspect the door gasket for damage and proper seal.

Alto-Shaam Converge CMC-H2H Specifications

General

Model	CMC-H2H
Type	Combination Oven
Brand	Alto-Shaam
Control Type	Touchscreen
Construction	Stainless Steel
Warranty	1 year parts and labor
Cooking Modes	Convection, Steam, Combination
Temperature Range	85°F to 575°F
Power Supply	208-240V, 60Hz, 3-phase
Water Supply	Required
Drain	Yes, Plumbed