D9 BAH0041-4 08.18
7
6.1.1.2
Calculation of the required minimum ballast weight at the front G
V min
of the tractor
to ensure steering capability ................................................................................................ 101
6.1.1.3 Calculation of the actual front axle load of the tractor T
V tat
................................................. 101
6.1.1.4 Calculation of the actual total weight of the combined tractor and implement .................... 101
6.1.1.5 Calculation of the actual rear axle load of the tractor T
H tat
.................................................. 101
6.1.1.6 Load-bearing capacity of the tractor tyres ........................................................................... 101
6.1.1.7 Table .................................................................................................................................... 102
6.2 Secure the tractor / implement against unintentional starting and rolling away ................. 103
6.3 Initial installation of the holders for the road safety bar ....................................................... 104
7 Coupling and uncoupling the implement .............................................. 105
7.1 Hydraulic hose lines ............................................................................................................. 107
7.1.1 Coupling the hydraulic hose lines ........................................................................................ 107
7.1.2 Uncoupling the hydraulic hose lines .................................................................................... 108
7.2 Coupling the implements ..................................................................................................... 109
7.2.1 Coupling the implement to the tractor .................................................................................. 111
7.2.2 Uncoupling the implement from the tractor .......................................................................... 113
8 Settings ..................................................................................................... 114
8.1 Folding the steps up and down ............................................................................................ 115
8.2 Placing the calibration trays on the funnel rail ..................................................................... 116
8.3 Setting the seed rate ............................................................................................................ 118
8.3.1 Seeding with the normal or fine seed metering wheel ......................................................... 118
8.3.2 Seeding with bean seed metering wheels ........................................................................... 120
8.3.3 Adjusting the sliding shutters ............................................................................................... 121
8.3.4 Bottom flap position ............................................................................................................. 122
8.3.5 Setting the digital filling level sensor .................................................................................... 122
8.3.6 Mounting the rapeseed insert .............................................................................................. 123
8.3.7 Agitator shaft support ........................................................................................................... 124
8.4 Filling the seed box .............................................................................................................. 125
8.5 Setting the seed rate using a calibration test ....................................................................... 128
8.5.1 Determining the gearbox setting using the calculating disc rule .......................................... 131
8.5.2 Hydr. seed rate remote control ............................................................................................ 132
8.6 Moving the track marker to the working/transport position .................................................. 134
8.6.1 Moving the track markers into working position with the marker changeover ..................... 135
8.6.2 Moving the track marker on the D9 2500/3000/3500 into working position ......................... 136
8.6.3 Moving the track markers on the D9 4000 into working position ......................................... 136
8.6.3.1 Adjusting the track marker length ........................................................................................ 137
8.6.4 Moving the track marker to transport position ...................................................................... 138
8.7 Adjusting and checking the seed placement depth ............................................................. 139
8.7.1 Coulter pressure adjustment, central ................................................................................... 139
8.7.2 Coulter pressure adjustment, hydraulic ............................................................................... 140
8.7.3 Adjusting the seed placement depth for the outer coulters ................................................. 141
8.7.4 Adjusting the depth control discs/wheels ............................................................................. 142
8.8 Attaching the band seeding shoe to the WS coulter ............................................................ 143
8.9 Adjusting the seed drill wheel mark eradicator .................................................................... 144
8.9.1 Moving the seed drill wheel mark eradicator into working position ...................................... 144
8.9.2 Moving the seed drill wheel mark eradicator into transport position .................................... 144
8.10 Adjusting the tractor wheel mark eradicator ........................................................................ 145
8.10.1 Tractor wheel mark eradicator, reinforced ........................................................................... 145
8.10.2 Tractor wheel mark eradicator, swivelling ............................................................................ 146
8.11 Adjusting the exact following harrow ................................................................................... 147
8.11.1 Working width of the exact following harrow ........................................................................ 147
8.11.2 Exact following harrow tine position ..................................................................................... 147
8.11.2.1 Adjusting the exact following harrow tine position by adjusting the screws ........................ 147
8.11.2.2 Adjusting the exact following harrow tine position by adjusting spindles ............................ 148
8.11.3 Exact following harrow pressure, manual adjustment ......................................................... 149
8.11.4 Exact following harrow pressure, hydraulic adjustment ....................................................... 149
8.11.5 Moving the exact following harrow to the working/transport position .................................. 150
8.11.5.1 Move the exact following harrow into working position ........................................................ 150
To Next Page