8
D9 BAH0041-4 08.18
8.11.5.2
Moving the exact following harrow into transport position .................................................. 150
8.12 Adjusting the roller harrow .................................................................................................. 151
8.12.1 Setting the pitch of the tines to the ground ......................................................................... 151
8.12.2 Setting the working depth adjustment of the harrow tines .................................................. 151
8.12.3 Setting the roller contact pressure ...................................................................................... 152
8.12.4 Lifting/lowering the roller harrow ......................................................................................... 154
8.12.4.1 Lifting the roller harrow (deactivate) .................................................................................... 154
8.12.4.2 Lowering the roller harrow (activate) ................................................................................... 155
8.13 Seed drills with mechanical or hydraulic actuation of the lay shaft coupling ..................... 156
8.13.1 Activating tramline control ................................................................................................... 156
8.13.2 Deactivating tramline control ............................................................................................... 157
8.14 Seed drills with electrical actuation of the lay shaft coupling ............................................. 157
8.14.1 Activating tramline control ................................................................................................... 157
8.14.2 Deactivating tramline control ............................................................................................... 157
8.15 Switching the left side of the seeding shaft ......................................................................... 158
8.15.1 Switching off the left side of the seeding shaft .................................................................... 158
8.15.2 Switching on the left side of the seeding shaft .................................................................... 158
8.16 Moving the tramline marker into working/transport position................................................ 159
8.16.1 Moving the tramline marker to working position .................................................................. 159
8.16.2 Moving the tramline markers to the transport position ........................................................ 160
8.17 Moving the road safety bar into transport/parking position ................................................. 161
9 Transportation ......................................................................................... 162
9.1 Moving the seed drill into transport position ........................................................................ 162
9.2 Legal regulations and safety ............................................................................................... 163
10 Use of the implement .............................................................................. 167
10.1 Initial operation .................................................................................................................... 168
10.2 Moving the implement from transport into working position ................................................ 169
10.3 During operation .................................................................................................................. 170
10.3.1 Overview of checks during operation .................................................................................. 170
10.3.2 Check the seed rate using the "AMALOG+" control terminal as an example ..................... 171
10.3.3 Track marker ....................................................................................................................... 172
10.3.4 Fill level indicator ................................................................................................................. 172
10.4 Turning at end of the field ................................................................................................... 173
10.5 End of work in the field ........................................................................................................ 174
10.6 Emptying the seed box and seed housing .......................................................................... 175
11 Faults ........................................................................................................ 178
11.1 Track marker boom shears off ............................................................................................ 178
11.2 Deviations between the preset and actual seeding rates ................................................... 179
12 Cleaning, maintenance and repairs ....................................................... 180
12.1 Safety .................................................................................................................................. 180
12.2 Cleaning the machine ......................................................................................................... 182
12.3 Shutdown of the implement over a long period of time ....................................................... 183
12.4 Lubrication ........................................................................................................................... 184
12.5 Maintenance schedule – overview ...................................................................................... 185
12.6 Checking the oil level in the Vario gearbox ......................................................................... 186
12.7 Checking roller chains and chain wheels ............................................................................ 187
12.8 Visual inspection of the upper and lower link pins .............................................................. 187
12.9 Inspection criteria for hydraulic hose lines .......................................................................... 188
12.9.1 Labelling of hydraulic hose lines ......................................................................................... 189
12.9.2 Installation and removal of hydraulic hose lines ................................................................. 190
12.10 Work to be performed in a specialist workshop .................................................................. 191
12.10.1 Adjusting the wheel scrapers .............................................................................................. 191
12.10.2 Setting the control box to control the tramline marker ........................................................ 191
12.10.3 Replacing the coulter tip (WS coulter) ................................................................................. 192
To Next Page