TM-F2OP-C1XN-01 xi
Figure 1-1 Power Supply Front Panel- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1–4
Figure 1-2 Power Supply Rear Panel (Low voltage (7.5 V to 100 V) model shown.) - 1–5
Figure 1-3 Programming and Monitoring SW1 Switch - - - - - - - - - - - - - - - - - - - - - 1–6
Figure 1-4 Programming and Monitoring J2 Connector- - - - - - - - - - - - - - - - - - - - - 1–7
Figure 2-1 Shipping or Storage Carton Label- - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–4
Figure 2-2 AC Input Cover and Strain Relief- - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–8
Figure 2-3 Maximum Load Wire Length for 1 V Line Drop- - - - - - - - - - - - - - - - - 2–13
Figure 2-4 Output Strain Relief and Cover - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–15
Figure 2-5 Typical Load Connection Hardware - - - - - - - - - - - - - - - - - - - - - - - - - 2–16
Figure 2-6 Output Voltage Connector- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–17
Figure 2-7 Single Load with Local Sensing (Default) - - - - - - - - - - - - - - - - - - - - - 2–18
Figure 2-8 Single Load with Remote Sensing - - - - - - - - - - - - - - - - - - - - - - - - - - 2–19
Figure 2-9 Multiple Loads with Local Sensing - - - - - - - - - - - - - - - - - - - - - - - - - 2–20
Figure 2-10 Multiple Loads with Remote Sensing - - - - - - - - - - - - - - - - - - - - - - - - 2–20
Figure 2-11 J10 Sense Connector - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–22
Figure 2-12 Connecting Remote Sense Lines - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–24
Figure 3-1 Operating Modes- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3–3
Figure 3-2 Series Operation of Multiple Supplies- - - - - - - - - - - - - - - - - - - - - - - - 3–12
Figure 3-3 Parallel Operation of Multiple Supplies- - - - - - - - - - - - - - - - - - - - - - - 3–14
Figure 3-4 Split Supply Operation of Multiple Supplies - - - - - - - - - - - - - - - - - - - 3–15
Figure 3-5 Split Supply Operation of Multiple Supplies - - - - - - - - - - - - - - - - - - - 3–16
Figure 4-1 Connecting Programming Sources to J2 Connector - - - - - - - - - - - - - - - - 4–6
Figure 5-1 Programming and Monitoring Calibration Locations- - - - - - - - - - - - - - - 5–4
Figure A-1 Typical Input Current Characteristics - - - - - - - - - - - - - - - - - - - - - - - - - A–7
Figure A-2 Dimensional Drawings - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - A–12
Figures
To Next Page
Loading...
