To Next PageTo Next PageHow to fix standing wave ratio limit exceeded error in Ametek Measuring Instruments?
If you see 'Standing wave ratio limit exceeded' on your Ametek Measuring Instruments, turn off the instrument and restart it. If the problem persists, please contact the SPECTRO Service Department.
What to do if power controller overflow occurs in Ametek SPECTRO ARCOS FHX3X?
If you see 'Power controller overflow' on your Ametek Measuring Instruments, turn off the instrument and restart it. If the problem persists, please contact the SPECTRO Service Department.
What to do if communication with the gas control system cannot be established in Ametek SPECTRO ARCOS FHX3X?
If you are experiencing a 'Communication with the gas control system cannot be established' error on your Ametek Measuring Instruments, turn off the instrument and restart it. If the problem persists, please contact the SPECTRO Service Department.
What to do if safety circuit error occurs in Ametek SPECTRO ARCOS FHX3X Measuring Instruments?
If you see 'Safety circuit error' on your Ametek Measuring Instruments, open and close all doors, then turn the instrument off and restart it. If the problem persists, please contact the SPECTRO Service Department.
What to do if plasma stopped due to Dmb timeout in Ametek SPECTRO ARCOS FHX3X?
If you see 'Plasma stopped (Dmb timeout)' on your Ametek Measuring Instruments, turn off the instrument and restart it. If the problem continues, contact the SPECTRO Service Department.
How to fix HF adjustment error in Ametek SPECTRO ARCOS FHX3X Measuring Instruments?
To resolve 'HF adjustment error' in your Ametek Measuring Instruments, check the working coil to ensure it is not deformed and is clean. The windings must be evenly distributed, and the coil must not be inclined to one side. If it is OK, repeat the test. If impurities have accumulated on the coil, clean it as described in the manual. If deformation occurred and/or the problem persists, please contact SPECTRO Service Department.
How to fix error in the plasma torch box extraction in Ametek Measuring Instruments?
To resolve an 'Error in the plasma torch box extraction' in your Ametek Measuring Instruments, check the extraction rate and adjust it to the values required in the operating manual, as the plasma torch box extraction is below the minimum setting.
Why is plasma too bright in Ametek SPECTRO ARCOS FHX3X Measuring Instruments?
If the plasma is too bright in your Ametek Measuring Instruments, decrease the power setting. Also, check the sample introduction system for leaks and eliminate them, as oxygen may be present.
What to do for housing extraction system error in Ametek Measuring Instruments?
If you encounter a 'Housing extraction system error' with your Ametek Measuring Instruments, it means the extraction rate of the instrument is below the minimum. Check the extraction rate and adjust it to the values required in the operating manual.
What to do if no channel is visible in the plasma in Ametek Measuring Instruments?
If there is no channel visible in the plasma of your Ametek Measuring Instruments, optimize the nebulizer gas flow. If the nebulizer is clogged, clean it. Also, check the spray chamber outlet for leaks and eliminate them.
General| Type | ICP-OES Spectrometer |
|---|---|
| Excitation Source | Inductively Coupled Plasma (ICP) |
| Detector | CCD |
| Plasma View | Radial and axial |
| Detector Type | CCD |
| Sample Type | Liquid |
| Power Requirements | 200-240 V, 50/60 Hz |
| Measurement Principle | Inductively Coupled Plasma Optical Emission Spectrometry (ICP-OES) |
Provides a general description of the SPECTRO ARCOS FHX3X.
Explains the working principles of the optical emission spectrometer.
Details the meaning of safety symbols used on the instrument.
Outlines mandatory safety instructions for instrument users.
Specifies operational zones and associated hazards.
Defines the scope and restrictions for instrument operation.
Lists conditions under which the instrument must not be operated.
Describes improper uses that can damage the instrument or cause hazards.
Highlights potential hazards that remain despite safety measures.
Provides safety instructions for using external sample introduction systems.
Identifies and describes components on the front of the instrument.
Identifies and describes components on the rear of the instrument.
Details the various connections available on the instrument's right side.
Identifies connections located in the analysis room area.
Describes the peristaltic pump and its maintenance.
Illustrates the components of the sample introduction system.
Details the parts within the plasma torch box.
Describes the plasma torch box for the EOP configuration.
Describes the plasma torch box with the optional DSOI.
Guidelines for safely transporting the instrument.
Specifies the necessary clearance for instrument installation.
Details required space for operation and maintenance access.
Step-by-step instructions for setting up the instrument.
Specifies optimal ambient temperature ranges for operation.
Defines acceptable dust levels for instrument environment.
Provides instructions for storing the instrument when not in use.
Information on gas inputs needed for instrument operation.
Details for the Argon gas supply.
Details for the optional Oxygen gas supply.
Instructions for connecting and managing the exhaust system.
Identifies and explains the function of the instrument's controls.
Actions to perform before switching on the instrument.
Step-by-step guide to power on and start the plasma.
Steps for safely turning off the instrument and plasma.
General section on conducting measurements.
Tasks to complete before starting a measurement.
Procedure for calibrating the instrument's optical system.
Steps for calibrating analytical methods.
Instructions on how to initiate a sample measurement.
Outlines recommended maintenance tasks and intervals.
Detailed procedure for cleaning the plasma torch.
Instructions for cleaning the induction coil.
Procedure for cleaning the standard Crossflow Nebulizer.
Procedure for cleaning the standard Scott Chamber.
Procedure to check the nebulizer's aerosol generation.
Steps to optimize the nebulizer's gas flow for performance.
Procedure for cleaning the Side-On Plasma Interface.
Steps for cleaning the SPI lens and associated parts.
Procedure for correctly installing the lens and SPI.
Procedure for cleaning the OPI (Multiview EOP only).
Steps for cleaning the instrument's sampler.
Detailed instructions for cleaning the instrument's lens.
Procedure for installing and cleaning the OPI.
Instructions for installing and removing the DSOI.
Procedure for cleaning various mirrors and adapters.
Steps for maintaining and replacing pump tubing.
Lists appropriate cleaning agents for different instrument parts.
