What to do if my Applied Biosystems GeneAmp PCR System 2700 Laboratory Equipment has no screen display and no response when turned on?
If your Applied Biosystems Laboratory Equipment shows no screen display and doesn't respond when you turn it on, check the following: Ensure the power switch is in the ON position, verify the power cord is properly connected, and inspect the fuses.
What to do if the printer is not responding to Applied Biosystems GeneAmp PCR System 2700 Laboratory Equipment?
If the printer is not responding to your Applied Biosystems Laboratory Equipment, check the printer connections and the power switch.
What to do if control panel is not responding on Applied Biosystems Laboratory Equipment?
If the control panel on your Applied Biosystems Laboratory Equipment is not responding, check for any keys that may be stuck in the down position and free them.
Why does my Applied Biosystems GeneAmp PCR System 2700 Laboratory Equipment printer fail?
Printer failures with Applied Biosystems Laboratory Equipment can occur due to an incorrect printer configuration or cable. Verify the printer settings are set to baud rate = 9600, no parity, one stop bit, and eight data bits. You can also purchase an Applied Biosystems printer cable.
Why is my Applied Biosystems GeneAmp PCR System 2700 making too much noise?
If your Applied Biosystems Laboratory Equipment is making too much noise, check for any obstructions in the vents.
Why is the cooling rate too slow in my Applied Biosystems GeneAmp PCR System 2700 Laboratory Equipment?
A slow cooling rate in your Applied Biosystems Laboratory Equipment can be caused by a warm ambient temperature. Move the instrument to a well-ventilated location with a temperature between 15–30 °C. It also can be caused by Peltier failure.
Why is the heating rate too slow on my Applied Biosystems GeneAmp PCR System 2700?
A slow heating rate on your Applied Biosystems Laboratory Equipment can be caused by Peltier failure.
Why is the cycling time too long for Applied Biosystems Laboratory Equipment?
An extended cycling time in Applied Biosystems Laboratory Equipment can be attributed to Peltier failure.
Why can’t my Applied Biosystems Laboratory Equipment reach the high or low temperature range?
If your Applied Biosystems Laboratory Equipment struggles to reach the desired high or low temperature range, this could be due to Peltier failure or an ambient temperature that is too warm.
What to do if Applied Biosystems Laboratory Equipment shows 'Valid range is' error?
If your Applied Biosystems Laboratory Equipment displays a 'Valid range is' error, it means you entered a number out of range. Re-enter a value within the specified parameters.
General| Temperature Range | 4°C to 99°C |
|---|---|
| Temperature Uniformity | ±0.5°C |
| Block Capacity | 96 x 0.2 mL tubes |
| Display | LCD |
| Interface | RS-232 |
| Temperature Accuracy | ±0.25°C (35-99.9°C) |
| Thermal Cycler Type | Peltier-based |
Defines alert words (IMPORTANT, CAUTION, WARNING, DANGER) and their symbols.
Covers safety for moving, lifting, and operating the instrument.
Provides warnings and guidelines for handling chemicals safely.
Details safety guidelines for handling and disposing of chemical waste.
Covers safety precautions related to grounding, fuses, power, and overvoltage.
Warns about hazards from moving parts and hot surfaces.
Describes the instrument, its features, and specifications.
Explains the control panel's components: screen, keys, and navigation.
Provides step-by-step instructions to turn on the instrument.
Explains how to add a user name for method separation and storage.
Instructs on how to modify an existing method's parameters.
Details procedures to start and stop a PCR run.
Provides procedures for loading samples with different tube configurations.
Step-by-step guide to initiating a PCR run on the instrument.
Explains how to pause a run and how to stop it completely.
Covers adding, modifying, or removing user accounts on the system.
Details the graphical representation of methods on the Create/Edit screen.
Explains how to modify methods using advanced features like holds and cycles.
Explains how to set instrument parameters like time, date, and printer settings.
Covers performing display and keypad diagnostic tests.
Details running Rate and Cycle tests to check heating/cooling systems.
Provides instructions for cleaning the sample wells and heated cover.
Step-by-step guide on how to safely replace instrument fuses.
Lists error messages, their descriptions, and recommended actions.
Lists error messages indicating potential hardware malfunctions and their solutions.
Provides a table of common problems, causes, and remedies.
To Next Page