Aries 2074112 - User Manual

To Next Page

ARIESAUTOMOTIVE.COM

•

NEED ASSISTANCE?

•

87 7. 2 8 7. 8 6 3 4

•

2074112-INS-RB

•

PAGE 1

INSTALLATION MANUAL

2074112

Parts List

1 Driver / left rocker step

1 Passenger / right rocker step

18 Flat washer, M8

18 Nylock nut, M8

Torque Speciﬁcations

Metric

M6 bolt 3 ft-lbs.

M8 bolt 7 ft-lbs.

M10 bolt 16 ft-lbs.

M12 bolt 28 ft-lbs.

SAE

1/4" bolt 3 ft-lbs.

5/16" bolt 7 ft-lbs.

3/8" bolt 16 ft-lbs.

7/16" bolt 20 ft-lbs.

1/2" bolt 28 ft-lbs.

Use above torque setting unless otherwise noted

Tools Required

Ratchet Socket set

Torque wrench Level

Level of Difﬁculty

Easy

Notes and Maintenance

Before you begin installation, read all instructions thoroughly.

Proper tools will improve the quality of installation and reduce the time required.

To protect the product, wax after installing. Regular waxing is recommended

to add a protective layer over the finish. Do not use any type of polish or wax

that may contain abrasives that could damage the finish.

Mild automotive detergent may be used to clean the product. Do not use dish detergent, abrasive

cleaners, abrasive pads, wire brushes or other similar products that may damage the ﬁnish.

Refer to the table to the left when securing hardware during the

installation process to help prevent damage to the product or vehicle.

Product Photo

Front

Rear

Product Registration

CURT Group stands behind our products with industry leading warranties.

You can help us continue to improve our product line and help us understand

your needs by registering your purchase by visiting:

warranty.curtgroup.com/surveys

At CURT Group, customer is king. We value your feedback and we use that information to make

improvements on our products. Please, take a minute and let us know how we are doing.

Need help?

Do you have a question about the Aries 2074112 and is the answer not in the manual?

Summary

Torque Specifications

Metric Torque Settings

Specifies torque values for M6, M8, M10, and M12 bolts in foot-pounds.

SAE Torque Settings

Specifies torque values for 1/4", 5/16", 3/8", 7/16", and 1/2" bolts in foot-pounds.

Notes and Maintenance Guidance

Pre-Installation and Cleaning

Read instructions thoroughly, use proper tools, and wax the product after installation for protection.

Cleaning and Finish Protection

Use mild detergent; avoid abrasive cleaners, pads, or brushes to prevent finish damage.

Product Registration Information

Installation Steps

Driver Side Mounting

Locate studs, remove debris, and attach driver-side step using M8 washer and nylock nut.

Tighten Brackets

Position rocker step and tighten all brackets securely to the vehicle.

Passenger Side Installation

Repeat steps one and two for the passenger side of the vehicle.

Post-Installation Checks

Ensure all mounting hardware remains tight through periodic inspections.

This document provides installation instructions and product information for the ARIES 2074112 Rocker Steps.

Function Description

The ARIES 2074112 Rocker Steps are designed to provide a sturdy and convenient step for easier entry and exit from a vehicle. They attach to the vehicle's rocker panel using existing factory studs, offering a secure and integrated solution. The installation process involves locating mounting studs, cleaning them, attaching the steps with specified hardware, and then tightening all components. The steps are provided as a driver-side and a passenger-side unit, ensuring complete coverage for the vehicle.

Important Technical Specifications

The product includes the following parts:

1 Driver / left rocker step
1 Passenger / right rocker step
18 Flat washer, M8
18 Nylock nut, M8

The installation requires common tools such as a ratchet, socket set, torque wrench, and a level.

Torque Specifications for Hardware: To ensure proper and safe installation, specific torque values are provided for different bolt sizes:

Metric Bolts:
- M6 bolt: 3 ft-lbs.
- M8 bolt: 7 ft-lbs.
- M10 bolt: 16 ft-lbs.
- M12 bolt: 28 ft-lbs.
SAE Bolts:
- 1/4" bolt: 3 ft-lbs.
- 5/16" bolt: 7 ft-lbs.
- 3/8" bolt: 16 ft-lbs.
- 7/16" bolt: 20 ft-lbs.
- 1/2" bolt: 28 ft-lbs.

These torque settings are crucial for preventing damage to the product or the vehicle and for ensuring the long-term stability of the installed steps. Users are instructed to use these torque settings unless otherwise noted in the installation steps.

Usage Features

The ARIES Rocker Steps are designed for straightforward installation, rated as "Easy" in terms of difficulty. The installation process is broken down into four clear steps:

Step 1: Locate Mounting Studs: On the driver's side, identify the three mounting studs along the inside edge of the vehicle. This step is visually supported by an image showing the location of these studs on the vehicle's underside.
Step 2: Attach Driver-Side Step: Starting at the front mounting location, users must first remove any debris from the factory studs. The driver-side step is then attached using an M8 flat washer and an M8 nylock nut. An important note advises applying anti-seize to the studs to prevent the nuts from seizing up. This process is repeated for the middle and rear mounting locations. Images illustrate the factory studs and the attachment process.
Step 3: Tighten Brackets: Once the rocker step is in position, all brackets must be tightened to the vehicle according to the specified torque values. An image shows a technician tightening the components under the vehicle.
Step 4: Repeat for Passenger Side and Final Checks: The entire process (steps one and two) is then repeated for the passenger side of the vehicle. Upon completion, users are congratulated on the installation of their new ARIES rocker steps. The manual emphasizes the importance of periodic inspections to ensure all mounting hardware remains tight, which is vital for safety and product longevity.

Maintenance Features

The manual provides essential notes on product maintenance to ensure the longevity and appearance of the rocker steps:

Pre-Installation: Users are advised to read all instructions thoroughly before beginning the installation. Using proper tools is highlighted as a way to improve installation quality and reduce the time required.
Post-Installation Protection: To protect the product's finish, waxing after installation is recommended. Regular waxing helps to add a protective layer.
Cleaning: Only mild automotive detergent should be used for cleaning the product.
Avoidance of Harmful Products: Users are explicitly warned against using any type of polish or wax that may contain abrasives, as these can damage the finish. Similarly, dish detergent, abrasive cleaners, abrasive pads, wire brushes, or other similar products that could damage the finish should be avoided.
Hardware Maintenance: The instruction to apply anti-seize to the studs during installation is a key maintenance tip to prevent nuts from seizing, which can complicate future adjustments or removal. Periodic inspections of all mounting hardware are crucial to ensure tightness and prevent potential issues.

Product Registration and Feedback

CURT Group, the manufacturer, stands behind its products with industry-leading warranties. Users are encouraged to register their purchase by visiting warranty.curtgroup.com/surveys. This registration helps CURT Group improve its product line and understand customer needs. The company values customer feedback and invites users to share their experience to contribute to product improvements.

In summary, the ARIES 2074112 Rocker Steps are a user-friendly accessory designed for easy installation and long-term durability, provided that the specified installation and maintenance guidelines are followed. The manual is comprehensive, covering everything from parts and tools to detailed installation steps, torque specifications, and crucial maintenance advice.