Why is there no light of cup holder LED ring in Atari Arcade Game Machines?
If there is no light of the cup holder LED ring on your Atari Arcade Game Machines, boot to restart. Also, check if the wire is loose. If problems persist, replace the LED ring board.
How to reduce noise from movement mechanism in Atari PONG 4P Arcade Game Machines?
If the movement mechanism has obvious noise on your Atari Arcade Game Machines, check and adjust the belt tension strength. Also, adjust the belt wheel position or replace the belt wheel. Finally, replace the belt if necessary.
What causes paddle and ball crash to offset in Atari PONG 4P?
If the paddle and ball crash to offset in your Atari Arcade Game Machines, it may be due to over suction of magnets. Adjust the rail magnet height downward.
What to do if Atari Arcade Game Machines game does not start?
If your Atari Arcade Game Machines game isn't starting, check the frame assembly connector to ensure it is not loose. If the frame assembly is faulty, contact UNIS Service.
How to fix paddle or ball offset in Atari PONG 4P?
To correct a paddle or ball offset on your Atari Arcade Game Machines: * First, check whether the playfield is fully positioned. * Clean the playfield, paddle, and ball. * Adjust the rail magnet height upward.
Why is the ball shaking in Atari Arcade Game Machines?
If the ball is shaking in your Atari Arcade Game Machines, it could be due to dirt on the bottom of the ball or the playfield. Use non-woven fabric with Glassy water to clean the bottom of the Ball.
How to troubleshoot Atari PONG 4P LED light strip not working?
If the LED light strip on your Atari Arcade Game Machines isn't working, check if the light strip connects properly. Also check the fuse. If problems persist, replace the light strip.
Why my Atari Arcade Game Machines power off?
If your Atari Arcade Game Machines is powering off, it might be because the circuit protector is turning the power switch off. Try turning the power switch back on. If this happens repeatedly, the machine has an anomaly, and you should contact UNIS Service.
How to fix no sound on Atari PONG 4P Arcade Game Machines?
If there's no sound on your Atari Arcade Game Machines, here are a few things to check: * First, make sure the volume isn't set too low – turn it up. * Then, check all the connectors to ensure they are properly connected. * Inspect the speaker for any faults. * Also, check the audio cable, reconnecting it or replacing it if necessary. * Finally, restart the audio driver.
What to do if the motor doesn’t work in Atari PONG 4P Arcade Game Machines?
If the motor isn’t working on your Atari Arcade Game Machines, it might be because the driver is broken, causing fuse overload protection. Replace the driver or check the motor. Also, check and replace the fuse.
General| Brand | Atari |
|---|---|
| Model | PONG 4P |
| Category | Arcade Game Machines |
| Language | English |
Warns about electric shock from high voltage components.
Warns about hot surfaces causing scalding.
Warns about parts being hot or causing electric shock.
Instructions on how to move the game machine safely during transport.
Guide to ensure the machine is placed on a level surface for proper operation.
Specifies the required space around the game for playing and maintenance.
Step-by-step guide for assembling the machine components.
Instructions for correctly positioning the ball and paddles on the playfield.
Procedure for converting the game's power supply voltage from 110V to 220V.
Safety precautions and recommendations for installing a card reader.
Guide on how to update the game's software for the monitor and cabinet.
Explains how to access and navigate the game's configuration menu.
Details how to adjust general audio, background music, and SFX volumes and themes.
Options for free play, mercy ticket, ticket for winner, and coins for credit settings.
Configuration for AI difficulty, points per game, game speed, and reverse control.
Options for setting time, alarms, and display dimming parameters.
Configuration for attract mode behavior, ambient light, and timeout.
Procedures for testing LEDs, motors, inputs, and performing auto-tests.
Options to reset game settings to default or clear all data.
Lists common issues, their possible causes, and recommended actions for troubleshooting.
Daily and monthly checks to ensure safe machine operation and proper working condition.
Step-by-step instructions for cleaning the game's playfield glass.
Guide for cleaning the game paddles and the ball.
Procedure for replacing the worn wool felt pads on the paddles.
Instructions for replacing the Teflon tape on the game ball due to wear.
Steps to access the internal movement mechanism for maintenance or repair.
Instructions for adjusting belt tension on the Y axle to resolve noise issues.
Instructions for adjusting belt tension on X and Paddle axles.
Steps to replace the 57MM Stepping motor used for the X axis.
Steps to replace the 57MM Stepping motor used for the Y axis.
Steps to replace the 42MM Stepping motor used for the paddle mechanism.
Instructions for replacing the motor driver unit.
Detailed steps for replacing the lifting motor assembly for the platform.
Detailed breakdown and diagram of the main cabinet assembly components.
Components and diagram for the rotational marquee assembly.
Components and diagram for the monitor assembly.
Diagram and list of parts for the movement mechanism assembly.
Components and diagram for the top case assembly.
Components and diagram for the base case assembly.
Components and diagram for the control panel assembly.
Components and diagrams for the L and R lifting mechanisms.
Components and diagrams for the playfield assembly.
Components and diagrams for the side light assemblies.
Components and diagrams for the paddle assemblies.
Components and diagrams for the ball assembly.
Identification of various decals and their placement on the machine.
To Next Page
