B&D Smart Pro SDO-9V3 - Battery Replacement; Battery Disposal Guidelines; Product Warranty Information

24
Smart Pro, Smart & Secure installation instructions
21. After Installation Care
When batteries reach the end of their usual life in accordance with Australian Battery Recycling Initiative please
follow the next simple steps for protecting the environment.
DO NOT throw the batteries in municipal waste. This symbol of the crossed out wheeled bin
indicates that the battery should not be placed in the municipal waste. Check your local
regulations for appropriate disposal of the batteries.
Recycling all batteries will have other environmental and social benets:
WARNING! Prior to disposal, recycling, or collection, all battery terminals must be securely
insulated with a non conductive material to prevent any two batteries from short circuiting and
generating heat during storage or transport. Battery terminals may be insulated with electrical
tape; or batteries may be individually packaged in a non conductive material
(e.g., plastic bag or original packaging).
21.3 Battery Disposal
21.2 Battery Replacement
• Some batteries are less toxic but hazardous for other
reasons. Lithium batteries can explode or catch re in landll,
while button cells are dangerous if swallowed by children.
Recycling offers a safe and environmentally responsible
solution for end of life batteries.
• Battery recycling recovers non-renewable materials such
as lead, cadmium, stella, zinc, manganese, cobalt, silver,
plastics and rare earth elements.
• Removal of batteries and other hazardous household
products from household waste facilitates the recovery of
organic materials through alternative waste technologies
such as composting. Batteries and heavy metals are known
contaminants in compost.
• The community supports recycling because it reduces
waste to landll and achieves environmental benets.
Warranty conditional on proper servicing as listed in 21.1 Service Checklist. Full details of the warranty are available
in your Owners Opener Handbook, from your nearest B&D ofce or visit the B&D Website bnd.com.au.
21.4 Warranty
WARNING! The Battery shall be disposed of properly, including keeping them away from children.
Even used batteries may cause injury.
Light Status Battery
Solid OK
Flashing Replace
No light Replace
3.0 CODING A REMOTE CONTROL
STEP ONE
The opener can only be operated from remote
controllers that have been programmed into its
memory. Up to 64 remotes can be programmed.
Battery Type: 1 x CR2032.
WARNING!: The battery is hazardous and must
be kept out of reach of children. The battery can
cause severe or fatal injuries within 2 hours or
less if swallowed or placed inside any part of the
body. If you suspect the battery has been
swallowed or placed inside any part of the body,
SEEK IMMEDIATE medical attention.
STEP TWO
STEP THREE
Switch power on and
remove controls cover
till remote
LED lit
Press
repeatedly
HOLD
Opener
ashes &
beeps
HOLD for 3 sec
HOLD for 3 sec
RELEASE
Release both
buttons
STEP FOUR
STEP FIVE
Press to test
tip
STEP ONE
4.0 CHANGING A BATTERY
HOLD
Check Light
Status Table
STEP TWO
tip
Use screwdriver
to remove
screws and
open
STEP THREE
Use non-metallic
object to push
out.
CODING REMOTE FROM THE OPENER
STEP ONE
STEP TWO
Take a pre-coded
remote and press the
button to duplicate
REMOTELY CODING A REMOTE CONTROL
Remotely coding works when you have a
pre-coded remote control and are in range of the
opener.
tip
Use a pen,
HOLD for 2 sec
the middle button
through the
coding hole
STEP THREE
Opener ashes & beeps
HOLD for 3 sec
HOLD for 3 sec
RELEASE
Take new
remote
RELEASE
STEP FIVE
Press to test
Opener stops ashing &
beeping
Then ret controls cover
WARNING! The battery is hazardous and must
be kept out of reach of children. The battery can
cause severe of fatal injuries within 2 hours or
less if swallowed or placed inside any part of
the body. If you suspect the battery has been
swallowed or placed inside any part of the body,
SEEK IMMEDIATE medical attention.