3AOFENE
w ww. b a o f eng r a d i o . u s ht t p : / / w w w. b a o f e ngr a d i o . u s
o
www.foscam.us
Menu Function and Description Chart
Menu
Function/Description
Available Settings
0
SQL (Squelch Level)
0-9
1 STEP (Frequency Step)
2.5/5/6.25/10/12.5/20/25/50kHz
2 TXP (Transmit Power)
HIGH/MID/LOW
3 SAVE (Battery Saver) OFF/1/2/3/4
4 VOX (Voice Operated Transmission) OFF/0-10
5 W/N (Wideband/Narrowband) WIDE/NARR
6 ABR (Display Illumination Time Length) OFF/l/2/3/4/5s
7 TDR (Dual Watch/Dual Reception) OFF/ON
8 BEEP (Keypad Beep Sound) OFF/ON
9 TOT (Transmission Timer) 15/30/45/60.../585/600seconds
10 R-DCS (Reception Digital Coded Squelch) OFF/D023N...D754I
11 R-CTS (Reception Continuous Tone Coded
Squelch)
67.0Hz...254.1Hz
12 T-DCS (Transmission Digital Coded Squelch) OFF/D023N...D754I
13 T-CTS (Transmission Continuous Tone Coded
Squelch)
67.0Hz...254.1Hz
14 VOICE (Voice Prompt) OFF/ON
15 ANI (Automatic Number Identification) Can
only be configured by PC software.
16 DTMFST (The DTMF tone of transmitting
code.)
OFF/DT-ST/ANI-ST/DT+ANI
17 S-CODE (Signal Code) Can only be
configured by PC software.
1 15 groups
18 SC-REV (Scan Resume Method) TO/CO/SE
19 PTT-ID (press or release the PTT button to
transmit the signal code)
OFF/BOT/EOT/BOTH
41
aAOFENE
www.baofengradio.us http://www.baofengradio.us
www.foscam.us
Customization
CTCSS
The Baofeng BF-F9V2+ allows for customization of both the power-on message (via
the Baofeng PC software), and the backlight color during the three states of transmission
(Transmit, Receive, and Standby).
Display
The LCD on the Baofeng BF-F9V2+ is backlit by multi-color LEDs, the color of
which can be pre-set from the menu system into a variety of colors.
To change the colors, follow the steps below:
Procedure: Changing the Backlight Color
1. Press the [MENU] button to enter the menu.
2. Enter one of the following on the numeric keypad:
a. [2] [9] to change the Standby color.
b. [3] [0] to change the Receive color.
c. [3] [1] to change the Transmit color.
3. Press the [MENU] button to select.
4. Use the [UP] and [DOWN] buttons to select the desired color.
5. Press the [MENU] button to confirm and save.
6. Press the [EXIT] button to exit the menu.
To change how long the backlight stays on, follow these steps:
Procedure: Setting Backlight Time-Out duration
1. Press the [MENU] button to enter the menu.
2. Enter [6] on the numeric keypad to get to the Backlight Time-Out settings.
3. Press the [MENU] button to select.
4. Use the [UP] and [DOWN] buttons to increase or decrease the amount of time
the backlight stays on.
5. Press the [MENU] button to confirm and save.
6. Press the [EXIT] button to exit the menu.
30
To Next Page
Loading...
