If this equipment does cause interference to radio or television reception, the user may try to correct the interference by one or m ore of the
following measures :
• Re-orientation of the receiving antenna for the radio or television.
• Relocate the equipment with respect to the receiver.
• Plug the equipment into a different outlet so that the equipment and receiver are on different branch circuits.
• Fasten cables connectors to the equipment by mounting screws.
Federal Communication Commission Interference Statement
You are cautioned that changes or modific ations not exp ressly approved by the part responsible for compliance could void the user ’s
authority to operate the equipme nt.
This equipm ent has been tested and found to com ply with the limits for a Class B digital de vice, pursuant to Part 15 of the FCC rules.
These limits are designed to pro vide reasonable protection against harmful interference in a residential installation. This equipment gen-
erates, uses and can r adiate radio frequency energy and, if not installed and used in accordance with the instructions, m ay cause harmful
interference to radio c omm unications. However, there is no guarantee that interference will not occ ur in a particular installation.
If this equipment does cause har mful interference to radio or television reception, which can be de termine
d by turning the equipm ent off
and on, the u ser is encouraged to try to correct the interference by one or more of the f ollowing measures:
• Reorient or relocate the receiving antenna.
• Increase the separation betw een the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to w hich the receiver is conn ected.
• Consult the dealer or an experienced radio/TV technician for help.
You ma y a ls o find helpful the following booklet, prepared by the FCC: "How to Identify and Resolve Radio-TV Interference Problems." This
booklet is available from the U.S. Government Printing Office, Washington D.C. 20402.
Changes and M odifications not expressly approved by the manufacturer or registrant of this equipment can void your a uthority to operate
this equipment under F ederal Com munica tions Commis sions rules.
In order to maintain compliance with FCC r egulations shielded cables must be us ed with this equipment. O peration with non-approved
equipment or unshielded cables is likely to result in interference to radio & tel
evision reception.
FCC RF Radiation E xpos ure Statement: This device is capable of o perating in 802.11a m ode. For 802.11a devices operating in the
frequency range of 5.15 - 5.25 GHz, they are restricted for indoor operations to reduce any potential harmful interference for Mobile Satellite
Services (MSS) in the US. WIFI Access Points that are capab le of allowing your device to operate in 802.11a mode (5 .15 - 5.25 GHz band)
are optimized for indoor use only. If your W IFI network is capable of operating in this mode, please restrict your WIFI use indoors to not
violate federal regulations to protect M obile Satellite Services.
Base Unit FC C ID: 2AAED-R9861520
Button FCC ID (m odel R9861006D01): X F6 -RS9110N1103
Button FCC ID (model R9861500D01): 2AAED-R 9861500D01
ClickShare Button R9861500D01 has been tested and meets the FCC RF ex posure guidelines.The max imum SAR value reported is
0.915W/kg.
Canada, Industry Canada (IC) Notices
This device complies with Industry Canada licence-exempt RSS stan dard(s). O peration is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept an y interference, inc luding interference that may cause undesired
operation of the dev ice.
Radio Frequency (RF) Exposure Information
The radiated output power of the Barco Wireless Device is below the Industry Canada (IC) radio frequency exposure limits. The Barco
Wireless Device should be used in such a manner such that the potential for human contact during normal operation is minimized.
Base Unit IC ID: IC: 9393B -R9861520
Button IC ID (model R 9861006D01): 8407A -RS9 110N1103
Button IC ID (model R 9861500D01): 9393B -R9861500D 01
IC Antenna statement
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain
approved for the transmitter by Industry Can ada. To reduce potential radio interference to other users, the antenna type and its gain s hould
be so chosen that the equivalent iso tropically rad iated power (e.i.r.p.) is not more than that necessary for successful communication.
To Next Page
Loading...
Need help?
General
