To Next PageTo Next PageWhy Bell System bellissimo maglock does not hold strongly?
If the maglock on your Bell System Intercom System does not hold strongly, it may be caused by voltage drop due to a cable that is too thin.
Why Bell System bellissimo lock works only from exit button?
If the lock on your Bell System Intercom System operates from the exit button but not the test button or phone, a normally closed switch may have been used for the exit button.
Why Bell System bellissimo view button doesn't select cameras correctly?
If repeatedly pressing 'view' doesn't select cameras in sequence as expected on your Bell System Intercom System: * Check that SW2-6 at all entrances is set for the correct number of cameras at that entrance. * Check the settings for SW3 if SW2-7 is enabled. * See section ‘Global View’.
What to do if my Bell System Intercom System videophone does not ring when called?
If your Bell System Intercom System videophone doesn't ring or flash when called, there might be several reasons: * The videophone might be off hook or muted. * There might be no power to the videophone. Check if the red mute lamp flashes when you pick up the handset. * There could be a fault in the data wiring (Data A or B broken). * The controller might be missing 0V on a separately powered videophone. * There may be a pushbutton wiring error. Try a short length at the controller.
Why Bell System bellissimo picture looks like a negative?
If you're experiencing an unstable picture with areas looking like a photographic negative on your Bell System Intercom System, the Video + and – or M and S wires may be reversed.
What to do if pressing view locks up Bell System Intercom System?
If pressing the 'view' button locks up your Bell System Intercom System, ensure that SW2-8 is OFF.
Why Bell System bellissimo lock light flashes when called?
If the green lock light on your Bell System Intercom System videophone flashes once when called, it means the videophone is set to an extension with no master present or responding.
Why does my Bell System Intercom System videophone reset?
The Bell System Intercom System videophone may be resetting due to a few potential issues. It could be caused by an intermittent short or overload in the power supply, especially if more than one extension is enabled for auto display. Alternatively, a short circuit in the lock output could be the cause; refer to ‘Lock Problems’ for further troubleshooting.
What to do if the Bell System bellissimo lock release doesn't work?
If the lock release on your Bell System Intercom System isn't working or just clicks without opening, several factors could be responsible: * Check for open or shorted connections to the Lock Release. * Voltage drop due to cable being too thin. * The lock current might be too high, causing the power supply to reset. * The lock release may be jammed due to being fitted too tightly.
What to do if my Bell System bellissimo Intercom System videophone doesn't ring or flash when called?
If your Bell System Intercom System videophone isn't ringing or flashing upon receiving a call, consider these potential causes: * The videophone might be off-hook or fully muted. * There might be no power reaching the videophone; verify that the red lamp flashes when the handset is picked up. * A fault in the data wiring (Data A or B broken). * Separately powered videophone might be missing 0V to controller. * Pushbutton wiring error; test with short length at controller.
Provides a general overview of the bellissimo video door entry system components and function.
Lists the key functionalities and capabilities of the 2-72 Way Video Entry System.
Explains the step-by-step process of a visitor call and resident response.
Describes the functions of the monitor controls, including contrast and volume.
Details the 'Auto Display' mode for automatic picture activation during a call.
Explains how to mute the videophone's ringing sound and its duration settings.
Describes how to view visitors without lifting the handset.
Explains the indicator for doors left open after a call.
Details how only one videophone can be active per call.
Notes that user activation is not available on multi-way systems.
Discusses the possibility of using one or two cameras, including CCTV integration.
Explains how to add additional videophones to a flat.
Covers support for fail-secure and fail-safe lock types, including magnetic locks.
Details the input for an exit button or fire switch for door release.
Explains the use of a time clock for tradesperson access.
Covers accessibility features for the Disability Discrimination Act.
Explains how to configure the system for multiple building entrances.
Details integration with gate controllers for shared entrances.
Describes using the videophone as a doorbell replacement.
Explains the slave output for operating external devices.
Lists the components included in various Bellissimo video kits.
Details available optional components and features for system expansion.
Provides guidance on optimal placement of the entrance panel for camera performance.
Specifies placement requirements for the door controller and its power supply.
Specifies placement requirements for the video controller and its power supply.
Details placement for the gate switch controller.
Explains how to overcome limitations with additional power supplies for videophones.
Outlines the system's 12V power supply needs and specific models.
Provides examples of controller and power supply configurations for different system sizes.
Details the required Cat5 cable type and specifications for system wiring.
Specifies maximum cable distances between video controllers and videophones.
Specifies maximum cable distances between door controllers and video controllers.
Specifies maximum cable distances between entrance panels and door controllers.
Specifies maximum cable distances for power supply connections.
Provides a checklist of required items and steps before installation.
General guidance on wiring procedures using Cat5 and 1mm² cables.
Instructions for mounting the entrance panel at the correct height and condition.
Instructions for wall mounting the videophone unit and securing it.
Details the BSA audio phone as an alternative extension unit.
Explains the connection and setting for electric door releases, including maglocks.
Important notes and considerations for fail-safe exit door releases.
Important notes and considerations for fail-secure exit door releases.
Details the function and wiring of the exit button input.
Explains the function of the door open switch for status indication.
Describes how to share a time clock signal across distributed areas.
Configuration of DIP SW1 (1-4) for talk time and videophone activation.
Configuration of DIP SW1 (5-8) for ringing time and call effects.
Configuration of DIP SW2 (1-3) for setting the lock release time.
Configuration of DIP SW2 (4-8) for various system functions like lock type and camera selection.
Configuration of DIP SW3 (1-8) for assigning numbers to cameras at the door.
Details jumper settings for camera termination, video gain, and DDA reassurance tones.
Details jumper settings for video gain and video termination on the BSC4 controller.
Configuration of SW6 rotary switch for videophone addressing on BSC4 controller.
Configuration of SW7 for adjusting address offset on BSC4 controller (Builds up to 6C).
Configuration of SW7 for adjusting address offset on BSC4 controller (Build 7 onwards).
Jumper configuration for extended addressing on BSC4 controller (Build 7).
Details special versions of BSC4 for addressing beyond standard ranges.
Jumper configuration for odd/even addressing of BSC4 outputs.
Configuration of DIP SW1 (1-4) for setting the mute duration on the videophone.
Configuration of DIP SW1 (5-8) for master/extension and auto display settings.
Details the jumper setting for video termination on the videophone.
Identifies common installation and wiring issues leading to system faults.
Provides tables for quick identification of power and call-related problems.
Troubleshooting guide for issues with lock release operation and maglocks.
Diagnoses and provides solutions for various video display issues.
Diagnoses and provides solutions for audio issues like feedback and low volume.
Technical specifications for the BSD8/72 door controller unit.
Technical specifications for the CAMBS-C colour camera.
Technical specifications for the BSC4 video controller.
Technical specifications for the BS Colour Videophone.
Technical specifications for the BSA audio phone.
Technical specifications for the Model 61 speech unit.
Technical specifications for the PS4 power supply unit.
Technical specifications for the 340C power supply unit.
Technical specifications for the battery-backed 840 power supply.
Technical specifications for the BSSW Gate Switcher.
Wiring instructions for connecting a local bell push to the videophone.
Explains the auxiliary ring output for DDA devices.
Provides options for camera wiring using twisted pair or coax cable.
Explains how to share a time clock signal using Cat5 wiring.
Wiring guide for connecting a Bellcode access controller to the system.
Wiring guide for connecting a Bell PAX1 proximity reader.
Wiring guide for connecting to gate controllers or other third-party access systems.
Wiring details for ACT 1000/2000/3000 proximity controllers.
Wiring details for ACT 100e proximity extenders.
Safety information and installation guidelines for the Model 840 power supply.
Safety information and installation guidelines for PS4 and 340C power supplies.
General| Brand | Bell System |
|---|---|
| Model | bellissimo |
| Category | Intercom System |
| Language | English |
