EasyManua.ls Logo

BendPak XpR-18C - User Manual

Default Icon
60 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
1
INSTALLATION AND OPERATION MANUAL
SHIPPING DAMAGE CLAIMS
When this equipment is shipped, title passes to the
purchaser upon receipt from the carrier. Consequently,
claims for the material damaged in shipment must be made
by the purchaser against the transportation company at the
time shipment is received.
BE SAFE
Your new lift was designed and built with safety in mind.
However, your overall safety can be increased by proper
training and thoughtful operation on the part of the operator.
DO NOT operate or repair this equipment without reading
this manual and the important safety instructions shown
inside.
1645 Lemonwood Dr.
Santa Paula, CA. 93060, USA
Toll Free 1-800-253-2363
Tel: 1-805-933-9970
Fax: 1-805-933-9160
wwwbendpak.com
Keep this operation manual near the
machine at all times. Make sure that
ALL USERS read this manual.
10,000 POUND CAPACITY
12,000 POUND CAPACITY
15,000 POUND CAPACITY
18,000 POUND CAPACITY
SURFACE MOUNTED
TWO-POST LIFTS
MODELS:
XPR-10C
XPR-10CX
XPR-10AC
XPR-10ACX
XPR-12C
XPR-15C
XPR-18C
VERSION A
PLEASE READ THE ENTIRE CONTENTS OF THIS MANUAL PRIOR TO
INSTALLATION AND OPERATION. BY PROCEEDING YOU AGREE THAT
YOU FULLY UNDERSTAND AND COMPREHEND THE FULL CONTENTS OF
THIS MANUAL. FORWARD THIS MANUAL TO ALL OPERATORS. FAILURE TO
OPERATE THIS EQUIPMENT AS DIRECTED MAY CAUSE INJURY OR DEATH.
MAN REV F 02-08-11
pn# 5900043
Pulley Pins. top and bottom
Arm Restraint Gears now Adjustable
Foot Guards on Column Base Bolt on
Top Trough Conguration
Lift Head Reinforcing Plates (Washers)
Micro Switch Cover Plate
Arm resistants left and right
Question and Answer IconNeed help?

Do you have a question about the BendPak XpR-18C and is the answer not in the manual?

BendPak XpR-18C Specifications

General IconGeneral
Lifting Capacity18, 000 lbs
Lifting Time60 seconds
Motor5 HP
Voltage220V
Pump Motor5 HP
Overall Length225" / 5, 715 mm
Power Requirement220V, 1Ph, 60Hz
Overall Height114 inches
Maximum Platform Width114 inches
Maximum Platform Length225" / 5, 715 mm
Power Requirements220V, 1Ph, 60Hz

Summary

PRODUCT WARRANTY

OWNERS RESPONSIBILITY

INSTALLER; OPERATOR PROTECTIVE EQUIPMENT

STEP 1 (Selecting Site)

STEP 2 (Floor Requirements)

CONCRETE SPECIFICATIONS

Specifies concrete requirements and specifications for safe installation.

STEP 5 (Installing The POWERSIDE Column)

STEP 6 (Mounting The OFFSIDE Column)

STEP 8 (Mounting the Hydraulic Power Unit)

STEP 9 (Installing the Safeties and Safety Cable)

STEP 10 (Installing Hydraulic Lines)

STEP 11 (Routing the Equalizers Cables)

STEP 14 (Installing the Lift Arms)

IMPORTANT LEVELING INSTRUCTIONS

IMPORTANT POWER-UNIT INSTALLATION NOTES

STEP 15 (Power Unit Hook Up)

STEP 16 (Lift Start Up; Final Adjustments)

POST-INSTALLATION CHECK-OFF

STEP 19 (Operation Instructions)

OWNER;EMPLOYER RESPONSIBILITIES

Defines responsibilities for safe lift operation and training.

LIFT OPERATION SAFETY

TO RAISE THE LIFT

TO LOWER THE LIFT

MAINTENANCE INSTRUCTIONS

WIRE ROPE INSPECTION AND MAINTENANCE

Safe Lift Operation

LIFT OPERATION; SAFETY

Critical safety considerations and operational procedures for lifts.

LIFT WILL NOT RAISE

MOTOR WILL NOT RUN

LIFT LOWERS SLOWLY OR NOT AT ALL

WILL NOT RAISE LOADED LIFT

LIFT WILL NOT STAY UP

Related product manuals