To Next PageTo Next PageWhat does '1999' mean on my Binder BD 53 display?
If you see the message '1999' on your Binder Climate chamber's controller display, it indicates a sensor rupture between the sensor and the controller, in that case contact BINDER service.
General| Brand | Binder |
|---|---|
| Model | BD 53 |
| Category | Climate chamber |
| Language | English |
Manual's purpose, limitations, and legal disclaimers.
Explains safety definitions, signal words, symbols, and panel structures.
Details the location of safety labels on the chamber for hazard identification.
Describes the essential technical and identification information on the chamber's type plate.
Crucial general safety guidelines for installation, operation, and maintenance.
Specifies the intended applications and limitations of the chambers for safe operation.
Emphasizes the need for clear, visible, and comprehensible operating instructions.
Outlines safety measures implemented by the manufacturer to prevent ignition and explosions.
Provides a labeled diagram identifying the main components of the chamber.
Guides the user on how to unpack and verify the chamber and its accessories.
Provides crucial safety instructions for handling and moving the chamber.
Specifies the permissible environmental conditions for storing the chamber.
Details requirements for the installation site, including ventilation and spacing.
Explains the procedures and precautions for connecting the chamber to the power supply.
Describes the optional connection of a suction plant and its potential influence.
Details the step-by-step process for turning on the chamber and its controller.
Explains how the heating status is indicated on the chamber's display.
Describes how to adjust the air change rate using the ventilation slide.
Explains how to view and set the desired temperature without using ramps.
Details how to set temperature points when using a programmed temperature ramp.
Explains the two main time-based operating modes: continuous and timed.
Describes how to switch between continuous and timer operation modes.
Explains the settings and behavior for continuous operation mode.
Guides on how to set the desired tempering time for timed operation.
Covers access to user-configurable settings for the controller.
Explains how to switch the temperature display between Celsius and Fahrenheit.
Details the procedure for programming temperature ramps for controlled heating.
Explains how to assign unique addresses for networked chambers.
Provides general operational notes and behavior of the controller.
Details the function, operation, and setting of the Class 2 safety device.
Explains the Class 3.1 safety device, its function, and adjustment.
Explains the function of the optional audible alarm for temperature deviations.
Details the optional software for chamber control and monitoring via PC.
Describes the optional data logger kit for temperature measurement and recording.
Explains the optional Pt100 sensor for precise temperature measurement.
Details the optional analog output for transmitting temperature data.
Describes the optional water-protected internal socket for powering devices inside the chamber.
Outlines recommended maintenance schedules and service procedures.
Provides instructions for cleaning and decontaminating the chamber.
Details the steps and approved cleaning agents for the chamber's interior and exterior.
Explains procedures for decontaminating the chamber after exposure to hazardous substances.
Outlines the process and requirements for returning a chamber for repair or service.
Provides guidelines for recycling or disposing of the chamber's transport packaging materials.
Explains how to properly decommission the chamber before disposal or long-term storage.
Details the specific disposal regulations for Germany according to WEEE.
Outlines disposal procedures for EU member states other than Germany, following WEEE.
Advises on disposal procedures for countries outside the European Union.
Explains that chambers are factory calibrated according to quality standards.
Defines and illustrates how the usable internal volume of the chamber is calculated.
Describes the over-current protection mechanisms, including fuses.
Presents detailed technical specifications for the BD series of chambers.
Lists comprehensive technical specifications for the ED series of chambers.
Provides detailed technical specifications for the FD series of chambers.
Lists standard equipment and optional accessories available for the BD series.
Details standard equipment and optional accessories for the ED series.
Lists standard equipment and optional accessories for the FD series.
Provides a catalog of accessories, spare parts, and their corresponding article numbers.
Official EU declaration confirming the BD series meets relevant directives.
Official EU declaration confirming the ED series meets relevant directives.
Official EU declaration confirming the FD series meets relevant directives.
Certificate for the GS mark of conformity issued by the German Social Accident Insurance.
Instructions and form for contamination clearance for regions outside North America.
Instructions and form for contamination clearance for USA and Canada.
