Binder C 170 - Page 86

To Next Page

To Previous Page

C (E3) 08/2015 page 86/93

Main Page

Table of Contents2
Safety5
Legal Considerations5
Structure of the Safety Instructions5
Signal Word Panel5
Safety Alert Symbol6
Pictograms6
Word Message Panel Structure7
Localization / Position of Safety Labels at the Unit7
Type Plate8
General Safety Instructions on Installing and Operating the CO9
Precautions When Working with CO 2 Gas11
Precautions When Handling Gas Cylinders11
Intended Use12
Unit Description13
The CO Measuring Principle13
Unit Overview14
Connection Panel at the Rear of the Unit16
Unit Doors16
Completeness of Delivery, Transportation, Storage, and Installation17
Unpacking, and Checking Equipment and Completeness of Delivery17
Guidelines for Safe Lifting and Transportation18
Storage18
Location of Installation and Ambient Conditions18
Installation and Connections21
Shelf Holder and Shelves21
CO Sensor22
Connecting the CO22
General Notes22
Sensor22
Water Pan23
Gas Connection24
Connecting the CO Gas Cylinder25
Gas Cylinder Connection Kit (Option)27
Electrical Connection28
Start up29
Function Overview of the Rp1 Controller29
Preset Factory Parameters30
Performance after Turning on the Unit30
Controller Rp1 Operating Modes31
Selecting and Setting the Operating Functions32
Operating Mode HAND32
Operating Mode USER: Advanced Settings34
Operating Mode LOCK: Locking/Unlocking of the Operating Functions' Settings by Operating Mode HAND38
Performance During and after Power Failures and Shut down39
Controller Rp1 Settings39
Altitude of the Installation Site above Sea Level39
Entering the Set Points of Temperature and CO41
Temperature Safety Devices42
Over Temperature Protective Device (Class 1)42
Safety Controller (Temperature Safety Device Class 3.1)42
Setting the Safety Controller Set Point Type43
Setting the Safety Controller Set Point44
Alarm Functions46
Alarm Functions Overview46
Resetting the Alarm Messages46
Zero-Voltage Relay Alarm Output47
Safety Controller Temperature Alarm48
Temperature Tolerance Range Alarm (High and Low Temperature)48
Door Open49
CO Tolerance Range Alarm (CO Over/Under Concentration)50
CO Pressure too Low50
Temperature Sensor Failure51
Failure of CO Sensor52
Error Messages52
Reference Measurements53
CO Reference Measuring53
Measuring the CO 2 Concentration Indirectly Via the Ph of the Cell Medium53
Measuring CO Directly Via Chemical Indicator Tubes54
Measuring CO Directly with an Electronic Infrared Measuring Device55
Temperature Reference Measurement55
Options55
Silicone Access Ports 30 MM / 1.18 In, Closable with 2 Silicone Plugs (8012-0558 Rear, 8012-0559 Left, 8012-0560 Right) (Option)55
Base on Castors (Option)56
Stacking Adapter for Direct Thermal Decoupled Stacking (Option)56
Analog Outputs for Temperature and CO (Option)56
Avoiding Microbial Contamination57
Cells and Media57
Laboratory Conditions / Equipment Around the Incubator57
Working and Behavior in the Lab57
Chamber Design and Equipment of the CO Incubator C 17058
Handling the CO Incubator C 17059
Cleaning, Decontamination / Disinfection, and Sterilization60
Cleaning60
Decontamination / Chemical Disinfection of the CO61
Incubator61
Disinfection of the CO63
Hot-Air Sterilization at 180 °C / 356 °F64
Overview64
Procedure for Hot-Air Sterilization64
Aborting the Hot-Air Sterilization67
Aborting the Hot-Air Sterilization Manually68
Aborting the Hot-Air Sterilization by Opening the Outer Door69
Aborting the Hot-Air Sterilization Using the Main Power Switch69
Maintenance, and Service70
Maintenance Intervals, Service70
Checking the Air Jacket Heating Fan70
Gas Inlet Fine Filter70
Sending the Unit Back to BINDER Gmbh71
Disposal72
Disposal of the Transport Packing72
Outer Unit Packing72
Packing Inside the Unit, Equipment72
Decommissioning73
Disposal of the Unit in the Federal Republic of Germany73
Disposal of the Unit in the Member States of the EC Except for the Federal Republic of Germany74
Disposal of the Unit in Non-Member States of the EC75
Troubleshooting76
Technical Description79
Factory Calibration and Adjustment79
Over Current Protection79
Definition of Usable Volume79
C 170 Technical Data80
Important Conversion Data for Non-SI Units81
Conversion Table for Gas Inlet Pressures, Bar - Psi81
Equipment and Options C 17082
Accessories and Spare Parts83
Dimensions C 17084
Certificates85
EC Declaration of Conformity85
Product Registration87
Contamination Clearance Certificate88
For Units Located Outside North America and Central America88
For Units in North America and Central America91

Binder C 170 - Page 86

Table of Contents

Related product manuals