Blanco CHOICE.All - User Manual

Other manuals for Blanco CHOICE.All

Assembly Instructions100 pages

Questions and Answers

J
Janice HughesAug 25, 2025
What to do if there is Error 2 (leak) in Blanco CHOICE.All?
- A
  Aaron MillerAug 25, 2025
  If you see Error 2, indicating a leak, check for water in the base cabinet. If water is present, trigger the kitchen or apartment fuse in the building’s electrical installation and disconnect the power supply. Check the system for water by viewing through the rear ventilation slits, tilting to allow any water to drain. After 15 minutes, reconnect the power supply and confirm the malfunction on the display by pressing 'OK'. Operate the system, dispensing 2 liters of each water type (hot, sparkling, and still), and wait 15 minutes. Then, inspect for any leaks in the base cabinet. If leaks persist, contact BLANCO Customer Service.
N
Nicholas GarciaAug 25, 2025
Why does my Blanco CHOICE.All show Error 9 (overheating) and the fan is noisy?
- A
  Adam WallsAug 26, 2025
  Error 9 indicates overheating, possibly accompanied by a noisy fan. First, wait 30 minutes to see if the error resolves itself automatically. If it doesn't, disconnect the power supply, wait 5 minutes, and then reconnect it. Check for nearby heat sources or heat accumulation in the base cabinet. Ensure proper ventilation by repositioning the water conditioning unit if needed, checking and improving ventilation openings in the base cabinet, and clearing any blockages from air inlets and outlets. If the issue continues, contact BLANCO Customer Service.
R
ricedavidAug 26, 2025
How to fix a weak or incorrect sparkling water spray pattern in Blanco CHOICE.All?
- B
  Brooke McdonaldAug 26, 2025
  To resolve a weak or incorrect sparkling water spray, replace the CO cylinder. Additionally, use the enclosed spanner to open the jet aerator on the mixer tap and clean it. Finally, check the installation to ensure corner valves are fully open, the filter and CO cylinder are fully screwed in, and the supply hose isn't kinked.
A
alison50Aug 27, 2025
What to do if Blanco CHOICE.All shows Error 3 - mixer tap communication?
- C
  Craig RobinsonAug 27, 2025
  If Error 3 appears, check the mixer tap cable connection on the rear of the water conditioning unit, pressing it in firmly or removing and re-inserting it. Disconnect the power supply, wait 5 minutes, and reconnect. If there's LED or halogen lighting nearby, disconnect it from the mains. Press 'OK' on the display to confirm the malfunction. Check the mixer tap cable for damage; if damaged, contact BLANCO Customer Service. If problems persist, contact BLANCO Customer Service.
C
christine23Aug 27, 2025
Why can't I dispense sparkling water from my Blanco CHOICE.All Plumbing Product?
- H
  hernandeznatalieAug 27, 2025
  If you cannot dispense sparkling water, first, check that the CO cylinder is fitted properly. A hissing sound when unscrewing the cylinder indicates correct insertion. Screw the CO cylinder in firmly, tightening it another 1/4 turn. If the issue persists, replace the cylinder with an original BLANCO CO cylinder, as only BLANCO CO cylinders should be used.
R
Rodney RuizAug 28, 2025
How to troubleshoot Error 1 (pump running time exceeded) on Blanco CHOICE.All?
- T
  Tammy GarnerAug 28, 2025
  To troubleshoot Error 1, start by opening the cold water corner valve. Check the supply hose from the corner valve to the water conditioning unit for any kinks and correct them if necessary. Verify the mixed water flow in the mixer tap; a malfunction in the building water installation may be the cause if the flow is not correct. Also, check the filter installation to ensure there is no gap between the filter attachment and filter head. Press 'OK' on the display to confirm the malfunction. If the problem persists, contact BLANCO Customer Service.
C
christinakochAug 29, 2025
Why is the sparkling water from my Blanco CHOICE.All not fizzy enough?
- M
  Mr. William HughesAug 29, 2025
  If your sparkling water lacks fizz, adjust the temperature setting to a colder level, as colder water allows CO 2 to be added more effectively. Allow the system to cool down for about 12 hours. Dispense 2 x 0.3 liters of sparkling water, wait another hour, and then re-evaluate. You can also try running the cleaning program.
R
Rebecca GrahamAug 30, 2025
What should I do if my Blanco CHOICE.All displays Error 21 - no water in the boiler?
- J
  Jason GravesAug 30, 2025
  If you encounter Error 21, check the supply hose between the safety assembly module and the water conditioning unit for kinks and correct them if necessary. Ensure the manual valve on the safety assembly module is open. Leave the system in the error state to allow the boiler to cool down. Once the boiler temperature falls below 35 °C, the system should automatically fill with water, though this may take several hours. If the issue persists, contact BLANCO Customer Service.
P
Pamela JohnsonAug 23, 2025
What causes Error 1 immediately after cleaning my Blanco CHOICE.All?
- N
  Nicholas TranAug 25, 2025
  Error 1 occurring directly after cleaning suggests the filter was not inserted correctly. Ensure the filter is correctly inserted and repeat the cleaning process with the filter in place.
V
Valerie BrownAug 31, 2025
What does Error 10 on my Blanco Plumbing Product mean?
- M
  Michelle GreerSep 1, 2025
  Error 10 indicates a display communication issue. Disconnect the power supply, wait 5 minutes, and then reconnect it. If the problem persists, contact BLANCO Customer Service.