To Next PageTo Next Page
Need help?Do you have a question about the BLT M880 and is the answer not in the manual?
Specifies the intended use of the M880 patient monitor for monitoring vital signs.
Details the components and layout of the patient monitor's main unit.
Provides crucial warnings and precautions for safe operation and handling of the patient monitor.
Explains the meaning of various symbols used throughout the manual for clarity and safety.
Provides instructions on how to power on the patient monitor and its initial system status.
Describes how to input and set patient-specific information for accurate monitoring.
Provides steps for safely powering down the patient monitor and its auto power-off settings.
Classifies the monitor's alarms into physiological, technical, and prompt messages.
Defines the severity levels for physiological and technical alarms.
Details the function of pausing alarms and how to cancel the pause.
Provides specific safety warnings related to CO2 measurement and its accessories.
Outlines the steps for connecting and performing CO2 monitoring.
Explains the procedure for zeroing the CO2 sensor for accurate readings.
Provides specific safety warnings for SpO2 sensor use and monitoring.
Outlines the steps for selecting, connecting, and applying the SpO2 sensor.
Details how to configure SpO2 measurement parameters and alarm limits.
Describes the interface for viewing stored CO2, RR, SpO2, and PR data.
Provides instructions for charging the patient monitor's battery.
Explains procedures for optimizing battery life through charge/discharge cycles.
Details the recommended methods and precautions for cleaning the monitor's exterior and screen.
Provides instructions for cleaning the SpO2 sensor.
Lists compatible accessories for the patient monitor and their part numbers.
Lists safety classifications and protection degrees for the device.
Details the technical specifications for CO2 and SpO2 measurements.
Shows the factory default limits and settings for CO2 and RR parameters.
Displays the factory default limits and settings for SpO2 and PR parameters.
Lists physiological alarm messages, their causes, and severity levels.
Lists technical alarm messages, their causes, and severity levels.
Specifies the intended use of the M880 patient monitor for monitoring vital signs.
Details the components and layout of the patient monitor's main unit.
Provides crucial warnings and precautions for safe operation and handling of the patient monitor.
Explains the meaning of various symbols used throughout the manual for clarity and safety.
Provides instructions on how to power on the patient monitor and its initial system status.
Describes how to input and set patient-specific information for accurate monitoring.
Provides steps for safely powering down the patient monitor and its auto power-off settings.
Classifies the monitor's alarms into physiological, technical, and prompt messages.
Defines the severity levels for physiological and technical alarms.
Details the function of pausing alarms and how to cancel the pause.
Provides specific safety warnings related to CO2 measurement and its accessories.
Outlines the steps for connecting and performing CO2 monitoring.
Explains the procedure for zeroing the CO2 sensor for accurate readings.
Provides specific safety warnings for SpO2 sensor use and monitoring.
Outlines the steps for selecting, connecting, and applying the SpO2 sensor.
Details how to configure SpO2 measurement parameters and alarm limits.
Describes the interface for viewing stored CO2, RR, SpO2, and PR data.
Provides instructions for charging the patient monitor's battery.
Explains procedures for optimizing battery life through charge/discharge cycles.
Details the recommended methods and precautions for cleaning the monitor's exterior and screen.
Provides instructions for cleaning the SpO2 sensor.
Lists compatible accessories for the patient monitor and their part numbers.
Lists safety classifications and protection degrees for the device.
Details the technical specifications for CO2 and SpO2 measurements.
Shows the factory default limits and settings for CO2 and RR parameters.
Displays the factory default limits and settings for SpO2 and PR parameters.
Lists physiological alarm messages, their causes, and severity levels.
Lists technical alarm messages, their causes, and severity levels.
General| Type | Laser Distance Meter |
|---|---|
| Accuracy | ±1.5mm |
| Temperature Compensation | Automatic |
| Measurement Range | 0.05m to 80m |
| Resolution | 1mm |
| Power Supply | 2 x AAA Batteries |
