Need help?Do you have a question about the BONFIGLIOLI ACTIVE Cube ACU 401-33 and is the answer not in the manual?
General| Brand | BONFIGLIOLI |
|---|---|
| Model | ACTIVE Cube ACU 401-33 |
| Category | Inverter |
| Language | English |
Identifies potential hazards that cannot be eliminated despite safety-compliant design, including electrical, electrostatic, and thermal risks.
Outlines directives operators must follow, including ensuring accessibility of regulations and compliance with country-specific laws.
Defines responsibilities for staff selection, qualification, and general work safety to prevent accidents and damage.
Provides safety instructions for the STO function, emphasizing proper installation and qualified commissioning.
Presents detailed technical data for ACU 201 inverters from 0.25 to 1.1 kW at 230 V, covering motor and mains sides.
Presents detailed technical data for ACU 201 inverters from 1.5 to 3.0 kW at 230 V, including mechanics and ambient conditions.
Presents detailed technical data for ACU 201 inverters from 4.0 to 9.2 kW at 230 V, covering output and input sides.
Presents detailed technical data for ACU 401 inverters from 0.25 to 1.5 kW at 400 V, including fuses and dimensions.
Presents detailed technical data for ACU 401 inverters from 1.85 to 4.0 kW at 400 V, including mechanics and output current.
Presents detailed technical data for ACU 401 inverters from 5.5 to 15.0 kW at 400 V, including ambient conditions and output current.
Presents detailed technical data for ACU 401 inverters from 18.5 to 30.0 kW at 400 V, covering output current and ambient conditions.
Presents detailed technical data for ACU 401 inverters from 37.0 to 65.0 kW at 400 V, including mechanics and output current.
Presents detailed technical data for ACU 401 inverters from 75.0 to 132.0 kW at 400 V, including mechanics and output current.
Details the standard mounting dimensions and installation possibilities for ACU 201 (up to 3.0 kW) and 401 (up to 4.0 kW).
Details the standard mounting dimensions and installation possibilities for ACU 201 (4.0 to 9.2 kW) and 401 (5.5 to 15.0 kW).
Details the standard mounting dimensions and installation possibilities for ACU 401 (18.5 to 30.0 kW) frequency inverters.
Details conductor cross-section dimensioning according to EN61800-5-1 and provides typical cross-sections for various connections.
Explains the configuration of control hardware and software for free assignment of functions to control terminals.
Presents a table summarizing possible combinations of functions and control methods available in different configurations.
Details how to select, edit, and save parameters, including navigating through parameter numbers and operation modes.
Guides the user through the setup process using the control unit, covering parameter settings and guided commissioning.
Details the procedure for checking and correcting the motor shaft's direction of rotation after installation.
Explains Configuration 30's role in assigning functions to control inputs/outputs and software functions.
Instructs to set rated parameters according to the motor's rating plate for control functions and methods.
Details parameterization of the 3-phase machine's starting behavior, including magnetization and IxR compensation.
Defines the stopping behavior of the 3-phase machine using Operation mode 630, selectable via logic signals.
Describes MFI1's configuration as voltage, current, or digital input, linking to various software functions via Operation mode 452.
Explains MFO1's configuration as digital, analog, or repetition frequency output, linked via parameters and Operation mode 550.
Details the selection of functions for digital outputs and relay output, depending on the parameterized configuration.
Explains adapting control signals to software functions via parameterizable inputs, allowing flexible use of digital signals.
Sets current limits to avoid inadmissible load and prevent fault switch-off, extending the current controller's capability.
Provides PID controller functionality for applications like pressure, volume flow, or speed control without extra components.
Includes additional functions like Slip Compensation and Current Limit Value Controller that supplement V/f characteristic behavior.
Covers control functions based on cascade control and machine model calculation, including Current Controller and Torque Controller.
Describes the brake chopper transistor and external brake resistor connection, including trigger threshold settings.
Covers monitoring mechanisms for recognizing thermal overload and protecting the motor, including motor protection switch.
Provides a chronological list of the last 16 fault messages, including error codes and their meanings.
Provides a structured list of parameters organized by function category, including setting ranges and chapter references.
To Next Page
