Bosch AMAX panel 4000 - Page 176

176 pages

To Previous Page

Bosch Sicherheitssysteme GmbH

Robert-Bosch-Ring 5

85630 Grasbrunn

Germany

www.boschsecurity.com

Main Page

Table of Contents3
AMAX Panel 4000 / AMAX Panel 4000 Table of Contents | en3
Graphics7
Safety8
Short Information9
System Overview10
Communication10
Zones10
Tamper Description10
Area10
User10
Programmable Output10
Key Switch10
Event Log10
Keypads10
Optional Modules and Peripheral Devices11
Keypad11
Brief Introduction11
Address Setting11
Wiring and Installation12
Test13
DX2010 Input Expansion Module13
Installation13
Wiring13
Tamper15
Address Setting15
Status Indicator16
Test16
DX3010 Output Expansion Module17
Installation17
Wiring17
Address Setting18
Test19
B426 Network Interface Module19
Brief Introduction19
Installation19
Wiring19
Address Setting20
Configuration20
Status Indicator20
Test21
ITS-DX4020-G Communication Module21
Brief Introduction21
Installation21
Connection21
Test22
RF 3227E RF Receiver23
Brief Introduction23
Installation23
Address Setting26
Wiring26
Status Indicator27
RFRC-OPT Radion Receiver27
Remote Programming Software27
Programming Key / Firmware Upgrade Key27
Installation28
Module Installation28
Battery Installation29
System Power up30
System Status Indicator31
Prerequisites for Certification Conform Installation31
EN 50131-3 Grade 2, Environmental Class 231
Settings32
Communication and Reporting32
Receiver Telephone Number /IP Address and Port32
Receiver Subscriber ID Number33
Receiver Transmission Format33
Receiver Network Programming Options37
Dual IP38
System Reporting39
Automatic Test Report44
Report Expiry Time44
Remote PC Settings44
Domestic Call45
Zones46
Zone Inputs46
Zone Function Settings / Zone Types47
Zone Function Settings / Zone Options53
Adding and Changing Zone57
Zone Indication Keypad and Event Log57
Outputs58
Onboard / Extension Output58
Output Events58
Output Options63
Alarm Siren Ringing Time64
Access Codes64
Installer Code64
User Codes64
System Settings - General65
Installer Access until Next Arming65
Force Arm When System Is in Trouble Condition65
Siren / PO-1+PO-2 Supervision65
Keypad 2 Button Alarm65
Phone Line Monitor65
Beep for Warning Devices65
Silence Warning Device When Disarmed65
Internal Siren Beep as Indication66
Battery Check Interval66
Cross Zone Timer66
AC Power Supply Fault Report Delay66
Date and Time66
Fault Inquiry66
Event Record Count Per Set/Unset Period66
System Tamper Indication in Area66
Quick Arming77
Keypad Settings77
Fault Report Settings77
Zone Tamper Bypass When DEOL Zone Is Bypassed78
System Settings - RF Options78
Area Settings78
Common Area78
Area Delay79
Keypad Area79
Configuration80
System Power up80
System Status Indicator80
Installer and User Code Commands80
Reset to Factory Default Settings82
Programming with Keypad82
LCD Keypad Menu Programming82
LED/LCD Keypad Programming90
PC Programming91
Direct Connection93
Modem Connection95
IP Connection100
Programming with the ICP-EZPK Programming Key105
Firmware Upgrade with the ICP-EZRU2 Upgrade Key106
Programming107
Communication and Reports Setting107
Zone Programming113
Output Programming124
Access Codes129
System Programming135
Keypad Usage and Operations153
Keypad Operating Instructions153
Arming and Disarming the System158
Arming the System158
Disarming the System159
Faults and Tamper Conditions159
System Fault or Tamper Analysis Mode in LED Keypad159
System Fault or Tamper Analysis Mode in Text Keypad161
System Test162
Siren Test162
Communication Test162
Walk Test Mode162
Event Log Recall Mode162
Reset the Control Panel163
- Codes164
- Change Individual Code165
- Keypad Fire Alarm166
- Troubleshooting167
- Maintenance170
- Technical Data171

Bosch AMAX panel 4000 - Page 176

Table of Contents

Related product manuals