Need help?Do you have a question about the Bosch Compress 5800i AW and is the answer not in the manual?
Explains signal words and symbols used in warnings for safety.
Provides general safety guidelines for installers and intended use of the unit.
Lists and illustrates the components included in the standard delivery of the indoor unit.
States compliance with European requirements and CE marking.
Details the indoor unit's intended use and integrated features.
Specifies the physical dimensions and required installation clearances for the unit.
Provides a detailed diagram and list of the indoor unit's internal components.
Lists applicable national and international regulations for installation.
Lists required and optional accessories for system operation.
Lists components not included but necessary for initial startup and operation.
Guides on selecting the location and environmental conditions for the indoor unit.
Details quality requirements for heating water and potable water.
Specifies crucial quality parameters for heating water to ensure system efficiency and longevity.
Discusses system volume impact on defrost cycle and potential energy draw.
Provides a method to determine if an additional expansion vessel is needed.
Outlines proper procedures for transporting and storing the indoor unit.
Details steps and methods for safely moving the unit to its final location.
Provides instructions for removing the front panel of the indoor unit.
Lists essential steps to perform during the installation process for a complete setup.
Offers guidelines for sizing DHW circulation lines in residential settings.
Covers the installation of optional accessories like the Connect-Key K30RF.
Details the specifications and limitations for external connections.
Explains the installation and settings for a safety thermostat.
Describes how to install and configure an accessory module for summary alarms.
Outlines specific requirements for installing the unit when cooling mode is utilized.
Provides instructions for setting up cooling mode without condensation.
Details the mounting procedure for the condensation sensor.
Addresses specific considerations for cooling mode with fan convectors.
Emphasizes the importance of proper insulation for pipes to prevent damage and condensation.
Covers general guidelines for connecting pipes, materials, and insulation.
Guides on connecting the indoor unit to the heat pump, including valve installation.
Explains how to connect the indoor unit to the primary heating system.
Details the connection process for the domestic hot water supply.
Provides a step-by-step guide for filling the heat pump, indoor unit, and heating system with water.
Highlights critical safety precautions related to electrical connections and shock hazards.
Provides general guidelines and regulations for electrical connections.
Explains the CAN-BUS connection and potential issues with incorrect wiring.
Details the connection of accessories using the EMS-BUS system.
Discusses the installation and function of temperature sensors.
Notes that the flow temperature sensor is pre-installed.
Guides on installing and connecting the outdoor temperature sensor.
Explains the use and connection of external inputs for control functions.
Covers the essential steps for connecting the main power supply to the unit.
Details cable types, diameters, and fuse specifications for the main power supply.
Illustrates how to route cables within the indoor unit for proper connection.
Details terminal connections for power supply within the electric box.
Shows electrical connections for 400V~3N input to the indoor unit.
Illustrates electrical connections for various accessories in the electric box.
Details the terminal connections for the XCU-THH (XCU HY) module.
A checklist to ensure all necessary steps are completed before system operation.
Guides through the initial setup and configuration wizard of the control panel.
Emphasizes the importance of proper ventilation for the system to prevent damage.
Details how to set and check the operating pressure of the heating system.
Explains how to check and set optimal operating temperatures for the heat pump.
Guides on configuring the electrical auxiliary heater settings.
Outlines the procedure for performing a function test of the system components.
Describes the function and reset procedure for the overheating protection.
Instructions for cleaning the particle filter to maintain system performance.
Details the importance and procedure for servicing the expansion vessel.
Provides instructions on how to safely drain the appliance.
Offers guidance on safely shutting down the heating system, including frost protection.
Lists the key technical specifications of the indoor unit and system.
Explains the different hydraulic configurations and system solutions.
Provides general explanations for various components in hydraulic configurations.
Details the hydraulic configuration for a heating circuit without a mixer.
Defines the symbols used in hydraulic diagrams and pipework.
Displays performance charts for circulation pumps.
Presents overall wiring diagrams for the system components.
Illustrates the wiring diagram for the XCU-THH (XCU HY) module.
Shows the standard power supply wiring diagram for the indoor unit.
Details cable types, lengths, and connections for sensors and bus cables.
Provides data for temperature sensor resistance values at different temperatures.
To Next Page
General