EasyManua.ls Logo

Bosch GTS1041A - User Manual

Bosch GTS1041A
144 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
1
IMPORTANT: IMPORTANT : IMPORTANTE:
Read Before Using Lire avant usage Leer antes de usar
For English Version Version française Versión en español
See page 2 Voir page 49 Ver la página 97
Operating/Safety Instructions
Consignes de sécurité/d’utilisation
Instrucciones de funcionamiento y seguridad
1-877-BOSCH99 (1-877-267-2499) www.boschtools.com
Call Toll Free for
Consumer Information
& Service Locations
Pour obtenir des informa-
tions et les adresses de nos
centres de
service après-vente,
appelez ce numéro gratuit
Llame gratis para
obtener información
para el consumidor y
ubicaciones de servicio
GTS1041A
1600A009XC 09-15.indb 1 9/14/15 1:51 PM

Questions and Answers

  • C
    Chelsea FoxAug 10, 2025
    Why won't my Bosch GTS1041A Saw start and the red light is flashing?
    • Q
      qbushAug 11, 2025
      The bypass switch might be stuck in the “ON” position, so turn the power switch off and ensure the bypass switch is not stuck. Also, check that an unused Activation Cartridge is correctly placed in the active position and securely connected. If the issue persists, the power switch may be burned out and should be replaced by an Authorized Bosch Service Center.
  • P
    Patricia WalshAug 16, 2025
    What to do if my Bosch Saw won't turn on?
    • D
      David ThomasAug 16, 2025
      First, check that the power cord is properly plugged in. If it is, inspect your fuse or circuit breaker and replace the fuse or reset the breaker if needed. If the issue persists, the cord may be damaged and should be replaced by an Authorized Bosch Service Center.
  • P
    Patrick HernandezAug 22, 2025
    What to do if the Bosch Saw cut binds and stalls when ripping?
    • B
      bishopmichaelAug 22, 2025
      The issue might be caused by a dull blade with an improper tooth set, so you should sharpen or replace the blade. Also, if you're using a warped board, make sure the concave or hollow side is facing “DOWN” and feed slowly. Other potential causes include the rip fence not being parallel to the blade, or the riving knife being out of alignment.
  • J
    Jennifer PhillipsAug 29, 2025
    How to reduce excessive vibration in my Bosch Saw?
    • A
      Alexandria TownsendAug 29, 2025
      Ensure that you tighten the tilt lock handle. If that doesn't solve the problem, the blade might be out of balance, so discard the blade and use a different one. Also, make sure the saw is securely mounted to its stand or workbench by tightening all mounting hardware.
  • G
    Gary StoneSep 3, 2025
    What to do if the red light on my Bosch GTS1041A Saw flashes immediately after plugging it in?
    • T
      Tyler GrimesSep 3, 2025
      This usually happens when the power switch is in the “ON” position when the saw is plugged in. Turn off the main switch, and the saw should operate normally.

Bosch GTS1041A Specifications

General IconGeneral
TypeTable Saw
Motor Power15 Amps
Max. Speed (No Load)5000 RPM
Voltage120 V
Blade Diameter10 inches
Maximum Cut Depth at 90 Degrees3-1/8 inches
Maximum Cut Depth at 45 Degrees2-1/4 inches
Arbor Size5/8 inches
Dust Port Diameter2-1/2 inches

Related product manuals