EasyManua.ls Logo

Bosch GTS18V-08 - User Manual

Bosch GTS18V-08
192 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Operating / Safety Instructions
Consignes d’utilisation / de sécurité
Instrucciones de funcionamiento y seguridad
Call Toll Free for Consumer Information & Service Locations
Pour obtenir des informations et les adresses de nos centres de service après-vente, appelez ce numéro gratuit
Llame gratis para obtener información para el consumidor y ubicaciones de servicio
For English Version
See page 2
●
Version française
Voir page 64
●
Versión en español
Ver la página 128
IMPORTANT
Read Before Using
●
IMPORTANT
Lire avant usage
●
IMPORTANTE
Leer antes de usar
1-877-BOSCH99 (1-877-267-2499) www.boschtools.com
GTS18V-08
Table Saw
Scie à table
Sierra de mesa
1609B07947GTS18V-08 OSI 08-2022.indd 1 8/3/22 2:44 PM

Table of Contents

Questions and Answers

  • R
    Roy WrightJul 28, 2025
    Why won't my Bosch GTS18V-08 start?
    • D
      Darren RodriguezJul 28, 2025
      There are several reasons why your Bosch Saw might not start. It could be that the Battery Pack is not attached or not fully inserted, the thermal protection in the circuit board may have tripped and needs to cool down, or the Battery Pack has discharged and needs to be charged or replaced. The temperature of the Battery Pack may also be outside the normal operating range, or the Electronic Motor Protection may have turned the tool off, requiring you to disconnect and replace the Battery Pack.
  • K
    Kimberly Pena DDSAug 1, 2025
    Why Bosch GTS18V-08 Saw blade does not come up to speed?
    • K
      kimberly62Aug 1, 2025
      The blade of your Bosch Saw might not reach full speed if the Battery Pack has a low charge, in which case you should charge it. Alternatively, the Battery Pack may be nearing the end of its life and reducing output, so consider replacing it. Overheating of the tool or Battery Pack can also cause this issue; allow them to cool down. Lastly, if the Battery Pack's temperature is too low, gradually warm it up before use.
  • U
    umooreAug 6, 2025
    What to do if Bosch GTS18V-08 Saw cut binds, burns, and stalls motor when ripping?
    • M
      Michael SuttonAug 6, 2025
      If your Bosch Saw's cut binds, burns, or stalls the motor while ripping, it could be due to several reasons. The Blade may be dull and needs replacement. If you're using a warped board, ensure the concave side faces down and feed slowly. Also, the Rip Fence might not be parallel to the Blade, or the Riving Knife could be out of alignment.
  • C
    Christopher HensonAug 10, 2025
    How to reduce excessive vibration in Bosch GTS18V-08?
    • C
      Courtney CooperAug 10, 2025
      Excessive vibration in your Bosch Saw can stem from a few causes. Ensure the Blade Bevel Lock Handle is tightened. An out-of-balance Blade can also cause vibration, so try using a different Blade. Make sure the saw is securely mounted to the stand or workbench by tightening all mounting hardware, and check that the Arbor Nut is properly tightened.
  • H
    Hannah CarterAug 14, 2025
    Why is the Blade Bevel Lock Handle Elevation Wheel hard to move on my Bosch Saw?
    • J
      John WhiteAug 14, 2025
      The Blade Bevel Lock Handle Elevation Wheel on your Bosch Saw might be hard to move because the Blade Bevel Lock Handle hasn't been loosened. Also, saw dust on the threads of the Threaded Elevation Rod can cause stiffness. Another reason can be that the undercarriage is filled with saw dust. Blow out any dust that has accumulated in the undercarriage, motor, or blade elevation gears.
  • A
    andersonclaireAug 18, 2025
    Why does my Bosch GTS18V-08 Saw have low power?
    • A
      Anna CruzAug 18, 2025
      Your Bosch Saw may have low power if you are not using a pro-core pack. For optimal performance, use an 8ah or 12ah Pro Core battery pack. While the saw will function with other batteries, it will operate with reduced power.
  • C
    chad97Aug 22, 2025
    What to do if Rip fence will not correctly clamp to rails on Bosch GTS18V-08?
    • C
      Carol GarciaAug 22, 2025
      If the Rip Fence on your Bosch Saw won't clamp correctly to the Rails, ensure that both ends of the Rip Fence are fully seated flush against the Rails before trying to latch the Rip Fence Lock Levers.

Summary

Safety Symbols

General Power Tool Safety Warnings

Safety Instructions for Table Saws

Kickback causes and related warnings

Getting to Know Your GTS18 V-08 Table Saw

Unpacking and Checking Contents

Unpacking the Table Saw

Assembly

Attaching the Smart Guard System

Guidance on attaching the primary safety system.

Selecting and Changing the Blade

Procedures for choosing and replacing the saw blade.

Attaching the Rip Fence

Steps for installing the rip fence for guiding cuts.

Adjustments

Adjusting the Blade Parallel to the Miter Gauge Slots

Calibrating blade alignment for accurate cuts.

Rip Fence Adjustments

Ensuring the rip fence is parallel to the blade for safety.

Adjusting the Riving Knife

Calibrating the riving knife for kickback prevention.

Adjusting 0° and 45° Positive Stops

Setting precise bevel angle stops.

Basic Table Saw Operations

Using the Rip Fence

Guide to using the rip fence for parallel cuts.

Using the Miter Gauge

Guide to using the miter gauge for crosscuts.

Ripping

Crosscutting

Non-Through Cutting

Using Stacked Dado Sets

Instructions for using dado blade sets for grooves.

Maintenance and Lubrication

Care of Blades

Cleaning

Anti-Kickback Device Maintenance

Troubleshooting

Saw will not start.

Blade does not come up to speed.

Low Power.

Cut binds, burns, stalls motor when ripping.

Bosch GTS18V-08 Specifications

General IconGeneral
TypeCordless Table Saw
Voltage18V
No-Load Speed4, 500 RPM
Battery TypeLithium-Ion
Blade Diameter8-1/4 inches
Bevel Setting0° - 47°
Max Cutting Depth at 90 Degrees57 mm (2-1/4")
Weight (without battery)21.2 lbs

Related product manuals