Solution 64
|
Installer Guide
|
Programming Overview
Bosch Security Systems | 11/05 | BLCC110I
4-5
Menu Reference Ta b l e
The Solution Controller includes a simple text menu system which makes all levels of programming extremely easy. Once a valid
PIN has been entered followed by the MENU key, the system will automatically determine which menus and options the PIN
holder has access to and only those items will be displayed.
There are four basic grouping levels used. Throughout the manual, symbols have been placed near each menu option so that you
can easily relate the authority level which is required to access them.
A =
= All (No PIN Required)
U =
= User PIN Has Access
M =
= Master PIN Has Access
I =
= Installer PIN Has Access
The following table lists all programming menus and the authority level required to access them.
0 Commands 1 Access 2 Areas
UMI 2-0-1 Turn Area On/O 1-0 Commands 2-0 Commands
UMI 2-0-2 Turn All Areas On MI 1-0-0 Erase User AUMI 2-0-0 Area Status
UMI 2-0-3 Turn All Areas O UMI 2-0-1 Turn Area On/O
UMI 2-0-4 Move To Area 1-1 PIN Codes UMI 2-0-2 Turn All Areas On
AUMI 2-0-5 Chime On/O UMI 1-1-0 Change Own PIN UMI 2-0-3 Turn All Areas O
UMI 1-1-0 Change Own PIN M 1-1-1 Change Other PIN UMI 2-0-4 Move To Area
AUMI 3-0-0 Zone Status MI 1-1-2 Add PIN AUMI 2-0-5 Chime On/O
AUMI 4-0-0 Output Status MI 1-1-3 Delete PIN
UMI 4-0-1 Turn Output On/O I 1-1-4 View PIN 2-1 Area Properties
MI 7-1-0 Set Date & Time MI 2-1-0 Area Name
UMI 3-0-5 Smoke Sensor Reset 1-2 Token I 2-1-1 General Options
UMI 3-9-0 Walk Test All Zones MI 1-2-0 Add Token I 2-1-2 Input Options
MI 4-9-0 External Siren Test MI 1-2-1 Delete Token I 2-1-3 Output Options
MI 4-9-1 Internal Siren Test MI 1-2-2 Token Status I 2-1-4 Reporting Options
MI 4-9-2 Strobe Test I 2-1-5 Strobe Trigger
MI 5-0-0 Set Domestic Number 1-3 RF Keyfob
UMI 5-0-1 Call/Answer RAS MI 1-3-0 Add Keyfob 2-2 Reporting
UMI 7-9-1 Battery Test MI 1-3-1 Delete Keyfob I 2-2-0 Account Dest 1
UMI 5-9-0 Test Dialler I 1-3-2 Test Keyfob I 2-2-1 Account Dest 2
I 7-0-8 Service Mode I 2-2-2 Open Close Route
UMI About 1-4 User Properties
MI 1-4-0 User Name 2-9 Area Testing
MI 1-4-1 Area Assignment I 2-9-0 Area Watch
I 1-4-2 User Options I 2-9-1 User Test Interval
MI 1-4-4 Timer Group I 2-9-2 Service Interval
MI 1-4-5 Access Assignment I 2-9-3 Test Options
I 1-5 Global Properties
I 1-5-0 PIN Length
I 1-5-1 PIN Retry Count
I 1-5-2 Installer PIN
I 1-5-3 PIN Expire Time
I 1-6 Prox Reader
I 1-6-0 Name
I 1-6-1 Area Assignment
I 1-6-2 Access Group
I 1-6-3 Reader Options
I 1-7 Lifts
I 1-9 Access Testing
To Next Page
Loading...
