Bosch Solution 64 - Comms Properties

Solution 64
|
Installer Guide
|
Comms Programming
9-4
Bosch Security Systems | 11/05 | BLCC110I
Comms > Telephone Number >
Call Forward On

-

MENU 5-1-6
1 Digits 32
•
6 1 , * 5 #
The panel is able to activate certain Telco services such as
Call Forwarding when the system is armed. Call forwarding
means that your customer will no longer need to remember
to manually activate the Call Forward On feature via the
telephone before leaving.
MENU 5-1-6 allows you to program the Call Forward On
number sequence. When armed the panel will automatically
seize the phone line and dial the number sequence and then
hang up.
In Australia, a typical sequence for activating the Call-Forward
On feature (All Calls) might be:
*61 0416123456 *20 #
*61 diversion type - Call Forward On - Immediate.
0416123456 Telephone number that you want calls to be
diverted to. Example shows mobile number.
*20 20 second delay
# end of sequence
Enter [MENU] + [5] + [1] + [6]. The keypad will display any
current Call Forward sequnces.
Call Forward On N001
Press  0-9 OK to SAVE
Using the numeric keys, enter all digits for the sequence. You
can change a single digit by scrolling the cursor left or right.
For special characters including, pause, * or #, use the up and
down arrow keys.
Press [OK] to save and exit or press [MENU] to exit without
saving.
Comms > Telephone Number >
Call Forward Off

-

MENU 5-1-7
1 Digits 32
# 6 1 #
The panel is also able to deactivate certain Telco services
such as Call Forwarding when the system is disarmed. This
means that your customer will no longer need to remember
to manually deactivate Call Forwarding when they disarm the
system.
MENU 5-1-7 allows you to program the Call Forward O
number sequence. When disarmed the panel will automatically
seize the phone line and dial the number sequence and then
hang up.
In Australia, a typical sequence for deactivating the Call-
Forward On feature (All Calls) might be:
*61 #
*61 = diversion type - Call Forward On - Immediate.
# = end of sequence
1)
2)
3)
Enter [MENU] + [5] + [1] + [7]. The keypad will display any
current Call Forward O sequences.
Call Forward Off N001
Press  0-9 OK to SAVE
Using the numeric keys, enter all digits for the sequence. You
can change a single digit by scrolling the cursor left or right.
For special characters including, pause, * or #, use the up and
down arrow keys.
Press [OK] to save and exit or press [MENU] to exit without
saving.
Comms Properties
Comms > Properties >
Call Attempt Count

MENU 5-2-0
0 6
This menu programs the maximum number of call attempts
the panel will make per destination in order to deliver the
report signal.
At factory default, the maximum number of call attempts
per event is 6 when reporting to a single destination and 12
attempts when reporting to 2 destinations. (6 attempts per
destination)
Domestic dialling also follows the call attempt count.
However, the call attempt count will be spread over total
phone numbers programmed for domestic reporting, ie. if
three domestic telephone numbers are programmed and the
call attempt count is 6, the panel will dial telephone number
1, telephone number 2 and telephone number 3, then repeat
once giving a total of 6 attempts). if the call is acknowledged
no further calls will be made for that event.
Press [MENU] + [5] + [2] + [0]. The keypad will display the
current number of call attempts per destination. (Default = 6).
Call Attempt Count N001
06
Press 0-9 OK to SAVE
Using the numeric keys, enter the required number of call
attempts per destination.Valid entries are 1 to 15. 0 = reporting
disabled
Press [OK] to save and exit or press [MENU] to exit without
saving.
i
Note
Setting the Call Attempt count to zero will disable all reporting
for Detination 1 and Destination 2
1)
2)
3)
1)
2)
3)