Solution 64
|
Installer Guide
|
Section 2 - Installing the Hardware
Bosch Security Systems | 11/05 | BLCC110I
2-3
Keypad DIP Switch Address Settings
Keypad To Address S1 S2 S3
Keypad 1 O O O
Keypad 2
On O O
Keypad 3 O On O
Keypad 4 On On O
Keypad 5 O O On
Keypad 6 On O On
Keypad 7 O On On
Keypad 8
On On On
Table 4: Keypad DIP Switch Address Settings
Status Icons & LED Indicators
The following table lists the function of each of the ICON
Symbols and LED Indicators on the Graphic Keypad Display.
Icon Status Meaning
The keypad can display the current status of up to
8 areas simultaneously via the Area Icon Indicators.
This option can be disabled in MENU 6-1-4
On
The area is turned All On or Part On
O The area is turned O
Flashing
Fast
The area has an alarm
On System power is normal
Flashing System power is missing
Flashing A re alarm is active
O No re alarm
On
Fire alarm in memory (Turn the area
All On and O to Clear).
On
The existing service or trouble
condition has been acknowledged.
O No service or trouble conditions exist
Flashing
A service / trouble condition is present
that has not been acknowledged.
On The area is turned Part On.
O The area is not turned Part On.
On The area is turned o.
O The area is turned All On or Part On
On The area is turned All On
O The area is turned O
On You have mail waiting to be read
O No Mail
On
Area is ready to turn on
(All On / Part On)
O Not ready, Zone Open
Red
LED
On
All On
Flashing Alarm
Green
LED
On Area is o.
Flashing Area not ready to turn on
Red &
Green
LED
Flashing Installer programming mode is active.
Table 5: ICON & LED Indicator Meanings
Keypad To n e s
Your keypad emits several distinct tones and displays text to
alert you to system events. The volume of the keypad tones
can be adjusted in MENU 6-1-0.
Type Meaning
Fire
Alarm
Tone
When a re zone sounds an alarm, the keypad
will sound 3 seconds on and 2 seconds o
(repeat).
Burglary
Alarm
Tone
When a burglary zone activates while your
system is turned on, your keypad emits a
continuous siren tone. It sounds for the time
set by your security company.
Trouble
Tone
When a system component is not functioning
properly, your keypad sounds 4 fast short
beeps followed by a 5 second pause (repeat).
Key Press
Tone
Pressing any key on the keypad sounds one
short beep, indicating that the key press is
accepted.
Entry
Delay
Tone
When you enter the premises through a zone
programmed for entry delay, the keypad
sound a Hi/Low tone to remind you to turn o
the area. If the area is not turned o before
the entry delay expires, an alarm condition
will sound and a report may be sent to your
alarm company.
Exit
Delay
Tone
After you turn an area All On, the keypad will
sound 1 short beep every second. During the
last 10 seconds fast short beeps will be heard.
If you don’t exit before the delay time expires
and an exit delay door is faulted, an alarm
occurs.
Error
Tone
If you press an incorrect key, your keypad will
sound a 2 second tone.
Menu
Mode
The keypad will sound a Hi / Lo tone to
indicate you have entered MENU Mode and a
Lo/Hi tone to indicate you have exited MENU
mode.
Chime
Tone
The keypad sounds fast short beeps to alert
you when a zone programmed for chime is
faulted or unsealled.
Table 6: Keypad Tone Meanings
To Next Page
Loading...
