Bosch Solution 64 - Page 72

Solution 64
|
Installer Guide
|
Comms Programming
9-10
Bosch Security Systems | 11/05 | BLCC110I
Comms > Dialler Reporting >
TX Format Dest 2

MENU 5-4-1
0 = Disable 1
1 = Contact ID 7 = Domestic
2 = SIA 8 = Voice 13 = Reserved
3 = Serial STU 9 = Panel 1 (Node 1) 14 = Reserved
4 = GSM 10 = Panel 2 (Node 2) 15 = Reserved
5 = WEB MAIL 11 = Panel 3 (Node 3)
6 = SMS 12 = Panel 4 (Node 4)
This menu allows you to program the transmission format
or language the panel will use to send event reports to
Destination 2.
Press [MENU] + [5] + [4] + [1]. The keypad will display the
current Transmission Format for Destination 2.
TX Format Dest 2 N001
01-Contact ID
Press 0-9 OK to SAVE
Use the up and down arrow keys to select the Transmission
Format required then Press [OK] to save and exit or press
[MENU] to exit without saving.
i
Note
Transmission Formats 9 -12 are not applicable on the Solution
64 control panel and should not be programmed. Other
formats may require additional hardware or add on modules to
function.
Comms > Dialler Reporting
Test Route

MENU 5-4-2
0 = Report Events To Log Only 1
1 = Report Events To Destination 1 + Log
2 = Report Events To Destination 2 + Log
3 = Report Events To Destination 1 & Destination 2 + Log
4 = Report Events To Destination 2 If Destination 1 Fails + Log
This menu programs which destination will be used to send
both manual and automatic test reports.
(*** System Wide Parameter ***)
Press [MENU] + [5] + [4] + [2]. The keypad will display the
current Test Route.
Test Route
01-Dest 1 + Log
Press 0-9 OK to SAVE
Use the up and down arrow keys to select the Test Route
required then Press [OK] to save and exit or press [MENU] to
exit without saving.
1)
2)
1)
2)
Comms > Dialler Reporting
Status Route

MENU 5-4-3
0 = Report Events To Log Only 1
1 = Report Events To Destination 1 + Log
2 = Report Events To Destination 2 + Log
3 = Report Events To Destination 1 & Destination 2 + Log
4 = Report Events To Destination 2 If Destination 1 Fails + Log
This menu sets the report destination that will be used to send
all system event reports.
(*** System Wide Parameter ***)
Press [MENU] + [5] + [4] + [3]. The keypad will display the
current Status Report route.
Status Route
01-Dest 1 + Log
Press 0-9 OK to SAVE
Use the up and down arrow keys to select the Test Route
required then Press [OK] to save and exit or press [MENU] to
exit without saving.
Comms > Dialler Reporting
Emergency Route

MENU 5-4-4
0 = Report Events To Log Only 1
1 = Report Events To Destination 1 + Log
2 = Report Events To Destination 2 + Log
3 = Report Events To Destination 1 & Destination 2 + Log
4 = Report Events To Destination 2 If Destination 1 Fails + Log
This menu programs the destination that all Keypad
emergency alarms are reported.
(*** System Wide Parameter ***)
Press [MENU] + [5] + [4] + [4]. The keypad will display the
current Emergency Route.
Emergency Route
01-Dest 1 + Log
Press 0-9 OK to SAVE
Use the up and down arrow keys to select the Keypad
Emergency route required then Press [OK] to save and exit or
press [MENU] to exit without saving.
1)
2)
1)
2)