Boss Snowplow RT3 - User Manual

Other manuals for Boss Snowplow RT3

Installation Instructions32 pages

Questions and Answers

G
Gerald MillerSep 13, 2025
Why does my Boss Snowplow RT3 Snow Blower not raise or raise slowly?
- C
  Cynthia KellySep 13, 2025
  If your Boss Snowplow Snow Blower is not raising or is raising slowly, ensure the hydraulic fluid level is within 2 cm (3/4 inch) of the reservoir top when lowered and in the V position. Check and connect any disconnected cables. If the battery is weak, replace it. If the pressure is less than 2,500 psi (at the end of the lift), the motor brushes may be defective, the pump pressure relief valve may be contaminated, damaged, or set too low, or the pump may be worn. Also, the RAISE solenoid valve may not be opening completely, consider replacing it.
M
michelehernandezSep 12, 2025
What to do if the pump motor does not run on my Boss Snowplow Snow Blower?
- Q
  qmorganSep 12, 2025
  If the pump motor on your Boss Snowplow Snow Blower isn't running, start by checking the cable connections. If they're connected, and voltage is present, the pump motor may have failed or the pump may have seized; consider replacing the motor brushes or the entire pump/motor assembly. If there's no voltage between a large terminal and ground, the cable between the battery and solenoid might be disconnected or broken. If no voltage is present, the solenoid may have failed and need replacement. If voltage is present at the solenoid, check the wire from its small terminal to ground for disconnections or breaks. If there's still no voltage, power from the relay may be disconnected; otherwise, inspect the wiring and controller switches.
R
Rebekah WilliamsSep 12, 2025
Why are all the plow and vehicle lights on at the same time on my Boss Snowplow Snow Blower?
- S
  Sean GonzalesSep 12, 2025
  If all of the plow and vehicle lights are on at the same time on your Boss Snowplow Snow Blower, the headlight adapters may not be installed correctly. Correctly install the headlight adapters.
R
Renee JohnstonSep 10, 2025
Why are the plow lights and truck lights on at the same time on my Boss Snowplow Snow Blower?
- B
  Brian ThomasSep 10, 2025
  If the plow lights and truck lights are on at the same time on your Boss Snowplow Snow Blower, the vehicle wire harness may be plugged into the vehicle headlight. Check the wiring connections.
J
Jessica CurtisSep 9, 2025
What to do if the SmartHitch2 does not attach to the plow on my Boss Snowplow Snow Blower?
- G
  Gregory CunninghamSep 9, 2025
  If the SmartHitch2 does not attach to the plow on your Boss Snowplow Snow Blower, turn the vehicle on and put the controller in the FLOAT position. If this doesn't work, the controller may be malfunctioning and need to be replaced. Also, check the valve block and SmartHitch2 switch for proper connections.
C
Chase TranAug 25, 2025
What to do if my Boss Snowplow Snow Blower does not raise or raises slowly?
- A
  Ashley FoxAug 25, 2025
  If your Boss Snowplow Snow Blower plow does not raise or raises slowly, first check the hydraulic-fluid level. If the fluid level is adequate, ensure that the power, ground, and control cables are properly connected. A weak or damaged battery can also cause this issue, so load test the battery and replace if needed. Inspect the motor brushes and replace them if they are worn. Verify that the pump pressure relief valve is set to 172 bar (2,500 psi); if it's lower, or if the valve is contaminated or damaged, clean or replace it. If the issue persists, the pump itself may be worn and require replacement. Finally, check the Raise and Lower control solenoid valves; if either is not opening completely or is stuck open, replace the valve.
B
Brooke TaylorSep 7, 2025
Why is fluid running out of the fill cap of the hydraulic pump on my Boss Snowplow Snow Blower?
- M
  Molly RobertsSep 7, 2025
  If fluid is running out of the fill cap of the hydraulic pump on your Boss Snowplow Snow Blower, avoid steeply sloped areas. The hydraulic fluid level should be within 2 cm (3/4 inch) of the top of the reservoir. Also, avoid hitting snowbanks too hard.
D
Daniel TerrySep 6, 2025
How to make my Boss Snowplow Snow Blower clean snow from low areas?
- M
  Mallory BellSep 6, 2025
  If your Boss Snowplow Snow Blower does not clean up snow from low areas, make sure the controller is in the FLOAT position. Activate the FLOAT feature on the controller.
R
rhodesmichaelSep 5, 2025
What causes the vehicle battery to die when turned off on a Boss Snowplow Snow Blower?
- T
  tiffany46Sep 5, 2025
  If the vehicle battery dies when the vehicle is turned off while using your Boss Snowplow Snow Blower, it might be because the wire harness isn’t connected to a keyed fuse source. Connect the wire harness to a keyed fuse source.
K
kevincarrollSep 4, 2025
Why does the blade on my Boss Snowplow Snow Blower trip too easily?
- D
  Dennis RodriguezSep 4, 2025
  If your Boss Snowplow Snow Blower blade trips too easily, check if the trip springs are loose or damaged. Tighten the springs if they are loose, or replace them if they are damaged. Also, ensure the pushbeam is at the correct height and adjust it if necessary.

Summary

Safety

Introduction

Overview of the manual's purpose and applicability.

Preparation Steps

Essential steps and considerations before operating or servicing the plow.

Safe Operation Guidelines

Critical rules for safe and correct operation of the snowplow.

Safety and Instructional Decals

Location and importance of safety decals for user guidance.

Installation Procedures

Straight-Blade Snowplow Mounting

Step-by-step guide for attaching the snowplow to the vehicle.

Straight-Blade Snowplow Removal

Step-by-step guide for detaching the snowplow from the vehicle.

Setup

Install Push Frame and Coupler

Attaching the push frame and coupler assembly to the plow blade.

Install Hydraulic Hoses

Connecting hydraulic hoses to the lift cylinder and pump.

Install Blade Guides and Fill Reservoir

Attaching blade guides and filling the hydraulic fluid reservoir.

Install Wire Harness

Connecting the electrical components of the snowplow system.

Mount Plow Controller

Installing the control unit within the vehicle cab.

Mount SmartTouch2 Controller

Specific instructions for mounting the SmartTouch2 controller.

Snowplow Mounting

Attaching the Plow

Detailed steps for physically attaching the snowplow to the vehicle.

Product Overview

Controls Description

Overview of the snowplow's control system and components.

SmartHitch2 Switch Operation

Function and operation of the SmartHitch2 switch.

Coupler Functionality

How the couplers secure the plow to the vehicle push beam.

SmartTouch2 Controller Operation

Operation of the SmartTouch2 controller for snowplow movement.

Operation

Performing the Snowplow Mount

Operational steps for mounting the snowplow to the vehicle.

Removing the Snowplow

Procedure for safely detaching the snowplow from the vehicle.

Hydraulic Fluid Checks

How to verify and add hydraulic fluid to the system.

Maintenance

Draining Hydraulic Fluid

Steps for completely draining the hydraulic fluid from the system.

Check Hydraulic Lines and Hoses

Inspection of hydraulic lines and hoses for damage or leaks.

Storage

Storing the Plow

Recommended procedures for storing the snowplow.

Removing Plow from Storage

Steps to take when taking the plow out of storage.

Troubleshooting

Pump Motor Issues

Diagnosing and fixing issues where the pump motor fails to operate.

Neutral Switch Issues

Troubleshooting when the pump motor runs with the switch in neutral.

Plow Lowering Problems

Identifying causes for the plow failing to lower.

Plow Lowering Speed Problems

Addressing the issue of the plow lowering at an excessive speed.

Plow Raising Problems

Diagnosing why the plow is not raising or is raising slowly.

Plowing Angle Issues

Troubleshooting unexpected plow angling during operation.

Angling Speed Problems

Fixing issues with the plow's angling function.

Lift Cylinder Leaks

Identifying and resolving hydraulic fluid leaks from lift cylinders.

Battery Drain Issues

Investigating battery drain when plow controls are in neutral or vehicle is off.

Snow Cleanup Effectiveness

Resolving issues with the plow's effectiveness in clearing low areas.

Pump Chatter

Diagnosing pump noise during raising or extending operations.

SmartHitch2 Attachment Failures

Resolving problems with the SmartHitch2 attachment mechanism.

System Schematics

Plow Side Electrical Schematic

Electrical diagram for the snowplow's control system.

Truck Side Electrical Schematic

Electrical diagram for the vehicle's connection to the snowplow.

Hydraulic Manifold Schematic

Diagram illustrating the hydraulic manifold system.

Boss Snowplow RT3 Specifications

General

Brand	Boss Snowplow
Model	RT3
Category	Snow Blower
Language	English

Related product manuals

THE SNOW PLOW SNOW PUSHER

2 pages

Boss Snowplow Snowrator SNR24001

48 pages

Boss Snowplow Snowrator MAG

36 pages