Why is the outlet water temperature too hot / cold in my Bristan Plumbing Product?
If your Bristan Plumbing Product's outlet water temperature is too hot or cold, start by checking the inlet filters for any blockages and clean them as necessary. Also, ensure that the installation conditions are within the recommended operating parameters.
What to do if only hot or cold water comes from Bristan Thermostatic Mixing Valve?
If you're getting only hot or cold water from your Bristan Thermostatic Mixing Valve, first check that the inlet water supplies are connected correctly: hot on the left and cold on the right when viewed from the front. Correct the pipework if necessary. Also, inspect the inlet filter for any blockages and clean or replace it, flushing the pipework before refitting.
Why is the water temperature too cold in my Bristan Buzz Plumbing Product?
If the water temperature from your Bristan Plumbing Product is too cold and the maximum water temperature is incorrectly set, adjust the hot water temperature or wait for the water to reheat if a stored system is in use. If you have an instantaneous water heater, increase the water flow rate through the system. Check the cartridge inlet filters, clean or replace them, and contact the boiler manufacturer if needed. Also, ensure that the water pressure is sufficient for the instantaneous water heater to ignite.
Why is water leaking from the showerhead of my Bristan Plumbing Product?
If water is leaking from the showerhead of your Bristan Plumbing Product, it may be normal for a short time after turning it off. Adjust the angle of the showerhead to vary the draining time. If the leak persists, the shower flow control valve may not be closing fully, possibly due to debris. Remove the flow control valve assembly and check it. Also, inspect the flow control valve seals for damage and replace as necessary.
How to fix no flow or low flow rate and varying temperatures in Bristan Plumbing Product?
If you experience no flow or low flow rate with your Bristan Plumbing Product, and the water temperature varies, here's what might be happening and how to address it: * Ensure the stop or service valve in the water supply pipework to the mixer valve is fully open. * If you have an instantaneous water heater, it might be cycling on and off due to low flow rate or pressure. Increase the water flow rate or pressure through the system. Contact the boiler manufacturer if needed. * Check that the water pressure is sufficient and balanced. If pressures are unbalanced then a pressure reducing valve should be used. * Clean or replace the inlet filter, and flush the pipework before refitting to address potential blockages. * Avoid using other water outlets while using the shower valve to ...
Details inlet connections, operating pressure range, and static pressure limits.
Specifies maximum outlet temperature and required water supply temperatures.
Controls water flow, includes Eco feature.
Adjustable temperature with 38°C safety stop and override.
Shower body remains cool during use.
Lists compatible water supply systems for installation.
Details minimum head requirements for gravity and pumped systems.
Emphasizes flushing pipework to clear debris before connection.
Specifies vertical distances for outlets above spill-over levels based on fitting size.
Steps for preparing and fitting the Fast Fit Kit, including pre-installation safety checks.
Details drilling wall holes and terminating supply pipework to the correct protrusion.
Covers attaching wall plates, olives, fixing bridges, and covers to the wall.
Steps for fitting filter washers, tightening fixing nuts, and attaching the diverter.
Instructions for assembling and mounting the rigid riser, including the rose and hose.
Steps for marking, drilling, and fixing the wall bracket securely to the wall.
Explains how to use the flow and temperature control handles.
Step-by-step guide to adjust the maximum water temperature setting.
Advice on cleaning the fitting to preserve its finish and avoid damage.
Instructions to resolve dripping issues by servicing the flow valve.
Guide for servicing the cartridge, especially in hard water areas, for optimum performance.
Addresses issues of low flow, no flow, and fluctuating temperatures with causes and remedies.
Explains causes of leaks from the showerhead and their solutions.
Covers problems with maximum, outlet, or set water temperatures being too hot or cold.
Addresses the issue of only hot or cold water being dispensed from the valve outlet.
Outlines conditions for warranty validity, purchase location, and access requirements.
Lists common causes of damage or defects not covered by the warranty.
Information on contacting Bristan for help, support, and technical advice.
Details on how to order spare parts and arrange for expert engineer assistance.
General| Mounting | Deck Mounted |
|---|---|
| Temperature Control | Manual |
| Display | No |
| Finish | Chrome |
| Handle Type | Lever |
| Material | Brass |
| Type | Basin Mixer |
| Control Type | Lever |
| Warranty | 5 Years |
To Next Page