65
Ch. 3 Functions
Functions
Mirror Printing function
(d + p)
This function prints your label so that the text
can be read from the adhesive side of the tape. If
mirror-printed labels are attached to glass or
some other transparent material, they can be
read correctly from the opposite side.
When ON is selected, the Mirror Printing indi-
cator at the top of the display comes on.
To print a mirror image of the text:
1 Hold down d and press p.
2 Press m or g until the desired setting is
displayed.
3 Press n to apply the setting.
Stamp Stencil function
(d + S)
The Stamp Stencil function allows you to
quickly and easily create your own stamp sten-
cil films for chemical etching. After inserting a
stamp film cassette, select this function to adjust
the text to a perfect thickness for the pre-inked
stamp film holders. Since the stamp holder is
reusable, just make a new stamp stencil film and
replace the one in the holder.
To make a stamp:
1 Type in the text, and then insert a medium
(3/4" (18-mm)-wide) or large (1" (24 mm)-
wide) stamp film cassette.
2 Hold down d and press S.
3 Press m or g until the desired setting is
displayed.
4 Press n. If ON was selected, the text is
automatically adjusted for stamps.
5 Press p to cut print resolution out of the
stamp stencil film.
6 After the stamp stencil film is cut off,
remove the backing paper from the stamp
stencil film and affix it to the ink pad of a
stamp film holder. Refer to Assembling
stamps on page 39.
NOTE
When using the Mirror Printing function, the text
should be printed on clear tape.
OFF
ON
NOTE
☞
To return the function to its default setting
(OFF), press the space bar.
☞
To return to the text without changing the for-
matting, press
e
(OR hold down
d
and
press
p
).
Length Margin Font Width Size
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
K
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
R
R
R
R
R
R
G
H
I
J
L
M
NO
AUTO 1.10 HELSINKI A AUTO
<<< P-touch >>>
1
:
_
NO
Length Margin Font Width Size
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
K
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
R
R
R
R
R
R
G
H
I
J
AUTO 1.10 HELSINKI A AUTO
MIRROR
OFF
L
M
NOTE
If a stamp is created using this function, be sure to
use the Tape Length function to select left and right
label margins of 1" (25 mm).
NOTE
☞
To return the function to its default setting
(OFF), press the space bar.
☞
To return to the text without changing the set-
ting for the Stamp function, press
e
(OR
hold down
d
and press
S
).
NO
Length Margin Font Width Size
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
K
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
R
R
R
R
R
R
G
H
I
J
AUTO 1.10 HELSINKI A AUTO
STAMP MODE
OFF
L
M
To Next Page
Loading...
Need help?
General
