GB
Page 2 of 62
INSTRUCTION, USE AND
MAINTENANCE MANUAL
SUMMARY
SYMBOLS USED IN THE MANUAL AND ON
THE MACHINE __________________________ 6
1.0 GENERAL INTRODUCTION _________ 8
1.1 Introduction ___________________________8
2.0 INTENDED USE ____________________ 8
2.1 Staff training __________________________8
3.0 SAFETY DEVICES __________________ 9
3.1 Residual risks _________________________9
4.0 GENERAL SAFETY RULES _________ 9
5.0 PACKING AND MOBILIZATION
FOR TRANSPORT _________________ 10
6.0 UNPACKING _______________________ 11
7.0 MOBILIZATION ____________________ 11
8.0 WORKING ENVIRONMENT
CONDITIONS ______________________ 11
8.1 Working area ________________________ 11
8.2 Lighting _____________________________ 12
9.0 MACHINE ASSEMBLY _____________ 12
9.1 Anchoring system ___________________ 12
9.2 Fixtures contained in the packing ___ 13
9.3 Assembly procedures ________________ 14
9.3.1 Fitting the mandrel on the flange _ 14
9.3.2 Fitting and removal of the
pneumatic mandrel on the
flange ___________________________ 14
9.3.3 Fitting the protection guard _____ 16
9.3.4 Monitor fitting
(LIBRAK380.3DTEC -
LIBRAK380P.3DTEC) ____________ 16
9.3.5 Monitor fitting
(LIBRAK430.3DTEC -
LIBRAK430P.3DTEC) ____________ 17
10.0 ELECTRICAL CONNECTION _______ 17
10.1 Electrical checks ____________________ 18
11.0 AIR CONNECTIONS _______________ 18
12.0 FITTING THE WHEEL ON THE
MANDREL _________________________ 19
12.1 Fitting of the wheel
(LIBRAK380.3DTEC -
LIBRAK430.3DTEC) _________________ 19
12.2 Fitting of the wheel
(LIBRAK380P.3DTEC -
LIBRAK430P.3DTEC) ________________ 20
12.3 Ultrasound sensor support
adjustment __________________________ 22
12.4 Correct positioning of the device
during the Run-out detection tyre
outer side (Optional) ________________ 22
13.0 CONTROL PANEL _________________ 23
14.0 WHEEL BALANCING ______________ 23
14.1 Switching the machine on and off ___ 23
14.2 Balancing programs setting _________ 25
14.2.1 Use of the machine automatic
system __________________________ 25
14.2.2 Programs setting through
“Measurement being
acquired” screen page ___________ 29
14.3 Indicative display of points where
to detect measures/to fit weight _____ 30
14.3.1 Weights positioning _____________ 30
14.4 Displaying the active/modifiable
field _________________________________ 30
14.5 Wheel balancing screen page
description __________________________ 30
14.5.1 Balancing mode _________________ 32
14.6 Standard balancing programs_______ 33
14.6.1 Static____________________________ 33
14.6.2 Static-1 __________________________ 34
14.6.3 Static-2 __________________________ 34
14.6.4 Dynamic_________________________ 34
14.6.5 ALU-S ___________________________ 34
14.6.6 ALU-S1 __________________________ 35
14.6.7 ALU-S2 __________________________ 35
14.6.8 ALU-1 ____________________________ 35
14.6.9 ALU-2 ____________________________ 35
14.6.10 ALU-3 __________________________ 36
14.6.11 ALU-4 __________________________ 36
14.7 Optional balancing programs _______ 36
14.7.1 ECO-WEIGHT mode ______________ 36
14.7.2 SPLIT mode _____________________ 38
14.7.3 Weights hidden behind spokes
mode ____________________________ 40
14.7.4 Matching mode __________________ 41
14.8 Special balancing programs _________ 44
14.8.1 Pax ______________________________ 44
14.9 Recalculation Function ______________ 44
14.10 Procedures for electronic RUN-OUT
measuring (tyre outer side)
(Optional) ___________________________ 44
15.0 USER MENU (OPTIONS AND
CALIBRATION) ____________________ 45
15.1 Options menu ________________________ 46
15.1.1 Lower weight limit ______________ 48
LIBRAK380.3DTEC - LIBRAK380P.3DTEC - LIBRAK430.3DTEC - LIBRAK430P.3DTEC
1297-M021-1_B
To Next Page
Loading...