Carrier 42C Series - Page 21

21
Fig. 16 — 42CK – Horizontal Telescoping Hideaway With Electric Heat
D
TOP VIEW
FRONT VIEW
PARTIAL REAR VIEW
RIGHT SIDE VIEW
A
20-3/4
[527]
1-5/8
[42]
11-1/4
[288]
12 [305] Min.
14 [356] Max.
1
[25]
E
Resilient Mounting
Grommet with 3/8 [10]
Dia. Holes (Typ. of 4)
1-1/2
[38]
1
[25]
1
[25]
25-7/8
[658]
20-3/4
[527]
See Notes
e,g,h
Optional
Service
Switch
10-1/4
[261]
Max.
4-5/8
[118]
H
Rear Duct Width
10-5/8
[271]
Unit Label and
Wiring Diagram
(See Note f)
Strip Heater
High Limit
Electric Strip
Heater Element
Optional “L” Shaped
Drip Lip, Shipped
Loose (See Note d)
Chilled Supply and Return
Connections
(See Supplemental Drawing
for Coil Stubout Locations)
10-1/4 [260]
(Size 06-12)
9 [229]
(Size 02-04)
1-3/4
[43]
3-3/4
[94]
1-1/2 [38] Knockout
(Typ. of 6)
7/8 [22] Knockout
(Typ. of 2)
(Typical Both Sides)
See Valve Pkg
Supplement for Dimensions
4-1/4
[108]
2
[52]
4-1/8
[106]
CR
CS
Detail A
Stub Out Locations
for Standard Coils
1-5/8
[40]
24
[609]
1-5/8
[40]
1-1/2
[37]
6
[155]
Optional Ducted
Rear Return
Flange 1 [24]
Hinged Bottom
Return Air Panel
Stamped Return
Air Grille and
1” [25] Filter
Return
Air
Supply
Air
F
7/8 [22] O.D.
Condensate Drain
Connection
6-1/8
[156]
B
C
LEGEND
CR — Cold Water Return
HR — Hot Water Return
CS — Cold Water Supply
HS — Hot Water Supply
UNIT
SIZE
42CK
DIMENSIONS in. [mm]
a,b,c,d,e,f,g,h,i,j,k
NOTE(S):
a. Right-hand units shown, left-hand opposite.
b. All dimensions are ± .25 [6]. Drawing not to scale.
c. Product specifications are subject to change without notice.
d. Drip lip recommended. Provided when valve package is ordered.
e. Control box size and position may vary. Consult factory.
f. Position may vary.
g. Service entrance is located on the rear of the control box with knockouts.
h. Units without service switch use the knockouts on the rear side of the control box.
i. Typical size 06 unit shown with 1-Motor and 2-Blower. Refer to table for variation.
j. See valve package supplemental for piping termination.
k. Field connection pipes will be shipped loose with valve packages.
QTY/UNIT
A B C D E F H Blower Motor
02 35 [889] 16 [406] 12-3/4 [324] 37 [940] 32 [813] 6 [152] 18-3/4 [476] 1 1
03 35 [889] 20 [508] 8-3/4 [225] 37 [940] 32 [813] 6 [152] 18-3/4 [476] 1 1
04 41 [1041] 26 [660] 8-3/4 [225] 43 [1092] 38 [965] 6 [152] 24-3/4 [629] 2 1
06 53 [1346] 31 [787] 15-3/4 [400] 55 [1397] 50 [1270] 7 [179] 35-3/4 [908] 2 1
08 53 [1346] 38 [965] 8-3/4 [225] 55 [1397] 50 [1270] 7 [179] 35-3/4 [908] 2 1
10 75 [1905] 52 [1321] 16-3/4 [425] 77 [1956] 72 [1829] 7 [179] 49-3/4 [1264] 4 2
12 75 [1905] 60 [1524] 8-3/4 [225] 77 [1956] 72 [1829] 7 [179] 49-3/4 [1264] 4 2