Carrier 42C Series - Page 20

20
Fig. 15 — 42CK Horizontal Telescoping Hideaway
4-5/8
[119]
Max.
1
[25]
Optional
Service
Switch
25-7/8
[658]
20-3/4
[527]
9-1/4
[236]
Max.
1
[25]
1
[25]
E
H
Rear Duct Width
10-5/8
[271]
1
[25]
Unit Label and Wiring
Diagram
(See Note f)
Optional "L" Shaped
Drip Lip. Shipped
Loose (See Note d)
Chilled/Hot Water Supply
and Return Connections
(See supplemental drawing for
coil stubout locations.)
Resilient Mounting Grommet
with 3/8 [10] Dia. Holes
(Typ. of 4)
Top View
Front View
Right Side View
10-1/4
[260]
(Size 06-12)
9
[229]
(Size 02-04)
1-3/4
[43]
3-3/4
[94]
7/8 [22] Knockout
(Typ. of 6)
Partial Rear View
(Typical Both Sides) See valve
pkg supplement for dimensions.
1-1/2 [38] Knockout
(Typ. of 6)
24
[609]
20-3/4
[527]
1-5/8
[40]
1-5/8
[40]
1-1/2
[37]
6
[155]
1-1/2
[38]
F
Supply
Air
Optional Duct
Rear Return
Flange 1 [24]
Hinged Bottom
Return Air Panel
Return
Air
7/8 [22] O.D.
Condensate
Drain Connection
Stamped Return
Air Grille and
1" [25] Filter
4-1/4
[108]
2-1/8
[53]
1
[25]
5-1/2
[141]
4-1/8
[106]
2-3/4
[71]
See Notes
e,g,h
A
B
C
D
6-1/8
[156]
1-5/8
[42]
11-1/4
[288]
12 [305] Min.
14 [356] Max.
LEGEND
CR — Cold Water Return
HR — Hot Water Return
CS — Cold Water Supply
HS — Hot Water Supply
UNIT
SIZE
42CK
DIMENSIONS in. [mm]
a,b,c,d,e,f,g,h,i,j,k
NOTE(S):
a. Right-hand units shown, left-hand opposite.
b. All dimensions are ± .25 [6]. Drawing not to scale.
c. Product specifications are subject to change without notice.
d. Drip lip recommended. Provided when valve package is ordered.
e. Control box size and position may vary. Consult factory.
f. Position may vary.
g. Service entrance is located on the rear of the control box with knockouts.
h. Units without service switch use the knockouts on the rear side of the control box.
i. Typical size 06 unit shown with 1-Motor and 2-Blower. Refer to table for variation.
j. See valve package supplemental for piping termination.
k. Field connection pipes will be shipped loose with valve packages.
QTY/UNIT
A B C D E F H Blower Motor
02 35 [889] 16 [406] 12-3/4 [324] 37 [940] 32 [813] 6 [152] 18-3/4 [476] 1 1
03 35 [889] 20 [508] 8-3/4 [225] 37 [940] 32 [813] 6 [152] 18-3/4 [476] 1 1
04 41 [1041] 26 [660] 8-3/4 [225] 43 [1092] 38 [965] 6 [152] 24-3/4 [629] 2 1
06 53 [1346] 31 [787] 15-3/4 [400] 55 [1397] 50 [1270] 7 [179] 35-3/4 [908] 2 1
08 53 [1346] 38 [965] 8-3/4 [225] 55 [1397] 50 [1270] 7 [179] 35-3/4 [908] 2 1
10 75 [1905] 52 [1321] 16-3/4 [425] 77 [1956] 72 [1829] 7 [179] 49-3/4 [1264] 4 2
12 75 [1905] 60 [1524] 8-3/4 [225] 77 [1956] 72 [1829] 7 [179] 49-3/4 [1264] 4 2