Carrier 42C Series - Page 19

19
Fig. 14 — 42CE Horizontal Furred-In With Plenum and Side Filter Access, With Same Side Piping and Controls
With Electric Heat Unit Dimensions
Resilient Mounting
Grommet with 3/8 [10]
Dia. Holes (Typ of 4)
Strip Heater High Limit
Electric Strip
Heater Element
19.13
[486]
1-1/2
[38]
1-1/4
[32]
2-1/4
[57]
E
C
A
Mounting Holes
Drain Pan with Valve Package
L
K
Rear/Bottom Return
Rear Mtg. Holes
6-1/4
[160]
Max.
Unit Label and
Wiring Diagram
(See Note f)
Filter Removal
(Both Sides)
Optional Service
Switch
See Note e
2
[51]
7/8 [22]
O.D.
Condensate
Drain
Top View
H
3/4
[19]
Typ
Front View
Chilled/Hot Water
Supply and Return
Connections
(See Detail A)
24-3/16
[614]
23-1/4
[589]
1" [25] Supply
Duct Collar
3/4
[20]
Supply
Air
F
G
12
[305]
Return
Air
10-1/2
[270]
Detail A
Coil Stub Out Locations
(Dimensions shown are for any coil.)
4-1/4
[108]
2-1/8
[53]
4-1/8
[106]
LEGEND
CR — Cold Water Return
HR — Hot Water Return
CS — Cold Water Supply
HS — Hot Water Supply
Right Side View
UNIT
SIZE
42CE
DIMENSIONS in. [mm]
a,b,c,d,e,f,g,h,i,j
NOTE(S):
a. Right-hand units shown, left-hand opposite.
b. All dimensions are ± .25 [6]. Drawing not to scale.
c. Product specifications are subject to change without notice.
d. Drip lip recommended. Provided when valve package is ordered.
e. Control box size and position may vary. Consult factory.
f. Position may vary.
g. Service entrance is located on the rear of the control box with knockouts.
h. Units without service switch use the knockouts on the rear side of the control box.
i. Typical size 06 unit shown with 1-Motor and 2-Blower. Refer to table for variation.
j. See valve package supplemental for piping termination.
QTY/UNIT
AC E FG H K LBlowerMotor
02 34 [864] 16 [406] 18-1/4 [464] 6-1/4 [159] 8-3/4 [222] 19-3/4 [502] 15-3/8 [391] 18-1/4 [464] 1 1
03 38 [965] 20 [508] 22-1/4 [565] 6-1/4 [159] 8-3/4 [222] 23-3/4 [603] 19-3/8 [493] 22-1/4 [565] 1 1
04 44 [1118] 26 [660] 28-1/4 [718] 6-1/4 [159] 8-3/4 [222] 29-3/4 [756] 25-3/8 [654] 28-1/4 [718] 2 1
06 49 [1245] 31 [787] 33-1/4 [845] 7-1/2 [191] 10 [254] 34-3/4 [883] 30-3/8 [772] 33-1/4 [845] 2 1
08 56 [1422] 38 [965] 40-1/4 [1022] 7-1/2 [191] 10 [254] 41-3/4 [1060] 37-3/8 [950] 40-1/4 [1022] 2 1
10 70 [1778] 52 [1321] 54-1/4 [1378] 7-1/2 [191] 10 [254] 55-3/4 [1416] 51-3/8 [1306] 54-1/4 [1378] 4 2
12 78 [1981] 60 [1524] 62-1/4 [1581] 7-1/2 [191] 10 [254] 63-3/4 [1619] 59-3/8 [1509] 62-1/4 [1581] 4 2