Carrier 42C Series - Application Data and Piping Components

18
Fig. 13 — 42CE Horizontal Furred-In With Plenum With Same Side Piping and Controls With Electric Heat
Unit Dimensions
Resilient Mounting
Grommet with 3/8 [10]
Dia. Holes (Typ. of 4)
L
K
Rear/Bottom Return
Rear Mtg. Holes
7-7/8
[199]
Unit Label and
Wiring Diagram
(See Note f)
Strip Heater
High Limit
19.13
[486]
Electric Strip
Heater Element
1-1/2
[38]
1-1/4
[32]
2-1/4
[19] Typ
E
C
B
Mounting Holes
Drain Pan with Valve Pkg
Optional Service
Switch
See Notes e,g,h
2
[51]
7/8 [22]
O.D.
Condensate
Drain
Top View
Front View
3/4
[19]
Typ
Chilled /Hot Water
Supply and Return
Connections
(See Detail A)
H
Right Side View
1” [25] Supply
Duct Collar
3/4
[20]
G
F
Supply
Air
24-3/16
[614]
23-1/4
[589]
Optional
Return Air
Location
10-1/2
[264]
Rear Access
Panel
Filter
Removal
Return
Air
11-1/4
[288]
Detail A
Coil Stub Out Locations
(Dimensions shown are for any coil.)
4-1/4
[108]
2-1/8
[53]
4-1/8
[108]
LEGEND
CR — Cold Water Return
HR — Hot Water Return
CS — Cold Water Supply
HS — Hot Water Supply
A
Drain Pan without Valve Pkg
UNIT
SIZE
42CE
DIMENSIONS in. (mm)
a,b,c,d,e,f,g,h,i,j
NOTE(S):
a. Right-hand units shown, left-hand opposite.
b. All dimensions are ± .25 [6]. Drawing not to scale.
c. Product specifications are subject to change without notice.
d. Drip lip recommended. Provided when valve package is ordered.
e. Control box size and position may vary. Consult factory.
f. Position may vary.
g. Service entrance is located on the rear of the control box with knockouts.
h. Units without service switch use the knockouts on the rear side of the control box.
i. Typical size 06 unit shown with 1-Motor and 2-Blower. Refer to table for variation.
j. See valve package supplemental for piping termination.
QTY/UNIT
A B C E F G H K L Blower Motor
02 28-1/2 [724] 34 [864] 16 [406] 18-1/4 [464] 6-1/4 [159] 8-3/4 [222] 19-3/4 [502] 15-3/8 [391] 18-1/4 [464] 1 1
03 32-1/2 [826] 38 [965] 20 [508] 22-1/4 [565] 6-1/4 [159] 8-3/4 [222] 23-3/4 [603] 19-3/8 [493] 22-1/4 [565] 1 1
04 38-1/2 [978] 44 [1118] 26 [660] 28-1/4 [718] 6-1/4 [159] 8-3/4 [222] 29-3/4 [756] 25-3/8 [654] 28-1/4 [718] 2 1
06 43-1/2 [1105] 49 [1245] 31 [787] 33-1/4 [845] 7-1/2 [191] 10 [254] 34-3/4 [883] 30-3/8 [772] 33-1/4 [845] 2 1
08 50-1/2 [1283] 56 [1422] 38 [965] 40-1/4 [1022] 7-1/2 [191] 10 [254] 41-3/4 [1060] 37-3/8 [950] 40-1/4 [1022] 2 1
10 64-1/2 [1638] 70 [1778] 52 [1321] 54-1/4 [1378] 7-1/2 [191] 10 [254] 55-3/4 [1416] 51-3/8 [1306] 54-1/4 [1378] 4 2
12 72-1/2 [1842] 78 [1981] 60 [1524] 62-1/4 [1581] 7-1/2 [191] 10 [254] 63-3/4 [1619] 59-3/8 [1509] 62-1/4 [1581] 4 2