Carrier 42C Series - Page 17

17
Fig. 12 — 42CE Horizontal Furred-In With Plenum and Side Filter Access, With Same Side Piping and Controls
Unit Dimensions
Unit Label and
Wiring Diagram
(See Note f )
Resilient Mounting
Grommet with 3/8 [10]
Dia. Holes (Typ. of 4)
15 [382]
L
K
Rear Mtg. Holes
Rear/Bottom Return
6
[151]
1-1/2
[38]
1-1/4
[32]
2-1/4
[57]
C
E
A
Drain Pan with Valve Pkg
15/16
[24]
FIlter Removal Both Sides
See Note e
7/8 [22]
O.D. Condensate
Drain
2
[51]
Mounting Holes
Top View
Front View
Right Side View
3/4
[19]
Typ
H
Chilled/Hot Water
Supply and Return
Connections
See Detail A
1" [25] Supply
Duct Collar
20
[507]
19
[485]
3/4
[20]
G
F
Supply
Air
12
[304]
Return
Air
10-1/2
[270]
Detail A
Coil Stub Out Locations
(Dimensions shown are for any coil.)
4-1/4
[108]
2-1/8
[53]
2-3/4
[71]
4-1/8
[106]
5-1/2
[141]
1
[25]
LEGEND
CR — Cold Water Return
HR — Hot Water Return
CS — Cold Water Supply
HS — Hot Water Supply
Optional Service
Switch
UNIT
SIZE
42CE
DIMENSIONS in. [mm]
a,b,c,d,e,f,g,h,i,j
NOTE(S):
a. Right-hand units shown, left-hand opposite.
b. All dimensions are ± .25 [6]. Drawing not to scale.
c. Product specifications are subject to change without notice.
d. Drip lip recommended. Provided when valve package is ordered.
e. Control box size and position may vary. Consult factory.
f. Position may vary.
g. Service entrance is located on the rear of the control box with knockouts.
h. Units without service switch use the knockouts on the rear side of the control box.
i. Typical size 06 unit shown with 1-Motor and 2-Blower. Refer to table for variation.
j. See valve package supplemental for piping termination.
QTY/UNIT
AC E FG H K LBlowerMotor
02 34 [864] 16 [406] 18-1/4 [464] 6-1/4 [159] 8-3/4 [222] 19-3/4 [502] 15-3/8 [391] 18-1/4 [464] 1 1
03 38 [965] 20 [508] 22-1/4 [565] 6-1/4 [159[ 8-3/4 [222] 23-3/4 [603] 19-3/8 [493] 22-1/4 [565] 1 1
04 44 [1118] 26 [660] 28-1/4 [718] 6-1/4 [159] 8-3/4 [222] 29-3/4 [756] 25-3/8 [654] 28-1/4 [718] 2 1
06 49 [1245] 31 [787) 33-1/4 [845] 7-1/2 [191] 10 [254] 34-3/4 [883] 30-3/8 [772] 33-1/4 [845] 2 1
08 56 [1422] 38 (965] 40-1/4 [1022] 7-1/2 [191] 10 [254] 41-3/4 [1060] 37-3/8 [950] 40-1/4 [1022] 2 1
10 70 [1778] 52 [1321] 54-1/4 [1378] 7-1/2 [191] 10 [254] 55-3/4 [1416] 51-3/8 [1306] 54-1/4 [1378] 4 2
12 78 [1981] 60 [1524] 62-1/4 [1581] 7-1/2 [191] 10 [254] 63-3/4 [1619] 59-3/8 [1509] 62-1/4 [1581] 4 2