Carrier 62X Series - STARTUP CHECKOUT; Verify Test Mode has been disabled (HomeSetupTest) by changing Run Test to “Off”; Verify all manual overrides have been turned off, unless set by air balance (HomeSetupMisc. SettingsMan Ovrd); Verify all sensor offsets have been turned off, unless set by calibration (HomeSetup Calibration)

CL-12
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -- - - - - - - - - - - - - - - - - - - -
CUT ALONG DOTTED LINE CUT ALONG DOTTED LINE
 With the supply fan operation at 100% speed or the balanced speed and the gas heat operating at low fire (50%
capacity for 2 stage units, 25% capacity for 4 stage units, 20% capacity for 5:1 modulating units, and 10% capacity for
10:1 modulating units), record the following information in the startup log:
· Outdoor air temperature (OAT)
· Unit supply air temperature (SAT)
· Inlet pressure (single furnace)
· Manifold pressure (single furnace)
· Flue gas CO and CO
2
levels (single furnace)
· Inducer draft fan pressure (single furnace)
Electric Heat (if equipped)
 With the supply fan operation at 100% speed or the balanced speed and the electric heater operating at 100%
capacity, record the following information in the startup log:
· Outdoor air temperature (OAT)
· Unit supply air temperature (SAT)
· Heater amp draw
 With the supply fan operation at 100% speed or the balanced speed and the electric heater operating at 50%
capacity, record the following information in the startup log:
· Outdoor air temperature (OAT)
· Unit supply air temperature (SAT)
· Heater amp draw
Hot Water Heat (if equipped)
 With the supply fan operation at 100% speed or the balanced speed and the electric heater operating at 50%
capacity, record the following information in the startup log:
· Outdoor air temperature (OAT)
· Unit supply air temperature (SAT)
· Heater amp draw
Field Installed Heat (if equipped)
 With the supply fan operation at 100% speed or the balanced speed and the electric heater operating at 100%
capacity, record the following information in the startup log:
· Heater operation and signal response
 With the supply fan operation at 100% speed or the balanced speed and the electric heater operating at 50%
capacity, record the following information in the startup log:
· Heater operation and signal response
STARTUP CHECKOUT
 Verify Test Mode has been disabled (HomeSetupTest) by changing Run Test to “Off”
 Verify all manual overrides have been turned off, unless set by air balance (HomeSetupMisc. SettingsMan
Ovrd)
 Verify all sensor offsets have been turned off, unless set by calibration (Home
Setup Calibration)
 Verify that the current time and date has been set in the controller (Home
SetupMisc. SettingsBAS Setup Set
Time and Date)
 Verify emergency shutdown is set to “Off” (Home
SetupTech. Setup.)
 Verify manual occupancy control is set to “Off” (Home
SetupTech. Setup.)
 Verify configured occupancy control is set to the last known setting (HomeSetupTech. Setup.)
 Set Enable Unit Operation to “On” (Home
SetupTech. Setup.)
 Verify no alarms are displayed (Home
Alarms)
The unit should now restore normal operation