Casio XJ-V10X User Manual

85
Light Control:
Configures the Light Control settings and Light Control Off
Mode settings. Setting 2 is valid for XJ-F Series projectors
only.
PMD RW 0: Bright, 1: Normal
2: Light Sensor On
3: Light Output 7
4: Light Output 6
5: Light Output 5
6: Light Output 4
7: Light Output 3
8: Light Output 2
9: Light Output 1
Freeze: Switches freeze on or off. FRZ RW 0: Off, 1: On
Keystone Correction:
Specifies the keystone correction setting as a value that
corresponds to the typical Setup Menu “Keystone
Correction” settings below.
0: Keystone Correction –60
60: Keystone Correction 0
120: Keystone Correction +60
Example: 65 here, specifies a setting equivalent to
Keystone Correction +5.
KST RW 0 to 120
Keystone Correction +/–:
Raises or lowers the current keystone correction setting
by 1.
+: KSP
–: KSM
W 0 to 120
Key: Operation executed when a key is pressed.
Settings 26 through 30 are valid for network model
projectors only.
Note
 Each KEY command setting corresponds to a
remote controller key. The projector operation that is
performed in response to a KEY command is
identical to the corresponding remote controller key
operation. When sending KEY commands to the
projector from an external device, make sure they
are sent in the same sequence that the
corresponding key operations are performed on the
remote controller.
KEY W 1: , 2: , 3: , 4: 
5: ENTER, 6: ESC, 10: FUNC
11: MENU, 12: POWER
13: AUTO, 14: INPUT
15: TIMER, 16: ASPECT
17: BLANK, 18: FREEZE
19: , 20: KEYSTONE +
21: KEYSTONE –
22: D-ZOOM +
23: D-ZOOM –
24: VOLUME +
25: VOLUME –
26: PLAY(R)
27: REWIND(s)
28: FORWARD(d)
29: PREVIOUS(S)
30: NEXT(T)
Setup Type:
Specifies how the projector is set up relative to screen for
projection.
0: Projection to a screen in front of the projector*
1
1: Ceiling mounted projection from behind the screen*
2
2: Projection from behind the screen*
1
3: Ceiling mounted projection to a screen in front of the
projector*
2
POS RW 0 to 3
APO: Used to change the Auto Power Off setting (trigger time
setting or Auto Power Off disable).
APO RW 0: Off, 1: 5 minutes
2: 10 minutes, 3: 15 minutes
4: 20 minutes, 5: 30 minutes
Error: Reads the projector error status. STS R 0: Normal, 1: Fan error
2: Temperature error
7: Light error, 16: Other error
Function
Command
Name
RW Settings

Casio XJ-V10X Specifications

General

Number of colors	1.073 billion colors
Native aspect ratio	4:3
Projection distance	1.95 - 2.87 m
Projection technology	DLP
Contrast ratio (typical)	20000:1
Screen size compatibility	30 - 300 \
Projection distance (tele)	3.33 - 4.85 m
Projector native resolution	XGA (1024x768)
Keystone correction, vertical	+ 30/ ± 30 °
Focus	Manual
Offset	50 %
Digital zoom	2 x
Optical zoom	1.5 x
Zoom capability	Yes
Focal length range	2.31 - 2.73 mm
DVI port	No
Audio (L/R) in	0
Serial interface type	RS-232C
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Maximum digital resolution	1920 x 1080 pixels
Operating temperature (T-T)	5 - 35 °C
Placement	Desktop, Ceiling
Product type	Standard throw projector
Product color	White
Power source	-
Power consumption (standby)	180 W
Service life of light source	10000 h
Service life of light source (economic mode)	6000 h
Analog signal format system	NTSC, PAL, PAL 60, PAL M, PAL N, SECAM

Weight and Dimensions

Width	299 mm
Height	97 mm
Weight	3500 g