EasyManua.ls Logo

Ceia THS/21E-3F - User Manual

Ceia THS/21E-3F
162 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
FI002K0018v1100UK – THS/21 Instruction manual for installation, use and maintenance
ORIGINAL INSTRUCTIONS 1
Industrial Metal Detectors
and Integrated Systems with Conveyor Belt
THS/21E - THS/21
Instruction manual
for installation, use
and maintenance
Document Date Hardware Software
FI002K0018v1100UK 2012-03-29 HV5.xx THSV5401 – ALMV5400
Read this manual carefully before installing, operating or carrying out maintenance on the device. Keep the manual in a
safe place for future reference and in perfect condition. This manual must accompany the device described herein in the
case of change of ownership and until the device is decommissioned.

Table of Contents

Questions and Answers

  • K
    Katherine GarzaJul 26, 2025
    Why is my Ceia THS/21E-3F Metal Detector giving false alarms?
    • R
      Rebecca TurnerJul 26, 2025
      False alarms on your Ceia Metal Detector may be due to electrical or mechanical disturbances. Try performing the Environmental Compatibility Check procedure with normal operating settings. If the source isn't identified, the issue might be a malfunction. In this case, disconnect all devices connected to the metal detector. If possible, connect it to a different power supply and earth source, ensuring the environment is free from interference. If the problem continues, it may require professional assistance.
  • S
    Sierra LongJul 31, 2025
    What to do if my Ceia THS/21E-3F Metal Detector doesn't detect test samples?
    • J
      joshua61Jul 31, 2025
      If your Ceia Metal Detector isn't alarming when using test samples, it could be due to a few reasons. First, ensure the correct product is selected. If not, repeat the Autolearn procedure to automatically set the sensitivity. Also, the sample might not have the right diameter for the current product. Set the default product and create a new one. Check that the samples are detected, if necessary by increasing the sensitivity value. If they are detected, samples with a bigger diameter must be used for the current product.
  • C
    Christopher FieldsAug 18, 2025
    How to troubleshoot a Ceia Metal Detector with a control panel display that is not on?
    • A
      alicianavarroAug 18, 2025
      If the control panel display on your Ceia Metal Detector is not on, check the connections between the SCD card and the ALM card. Disconnect all the devices connected, switch off the system and switch it on again after a few minutes, if self-resetting protective devices have been activated. If the Metal Detector can expel metal masses, verify the RCU card is correctly connected to the ALM card. Otherwise, inspect the state of fuse F10 (and F11/F12 for Conveyor Control System) and ensure the power supply voltage is within the permitted range.
  • W
    wilsonsarahNov 5, 2025
    How to fix a Ceia THS/21E-3F Metal Detector conveyor belt that won't start?
    • M
      markjacksonNov 5, 2025
      If the conveyor belt in your Ceia Metal Detector system isn't starting, there are several things to check: * If the belt running indicator is off, ensure the KT parameter isn't zero and is correctly set. Also, inspect the inverter connections inside the power supply unit. * If the belt running indicator is on, verify the inverter is correctly configured for the connected motor (check NMV, NMF, NMC parameters) and inspect the motor connections. For non-integrated systems, ensure the connected motor is compatible with the inverter output characteristics. * If the belt running indicator is flashing, check that the FOLLOWING CONVEYOR input is active or, if it is not used, set FC=OFF. * If the belt running indicator is only on when the key is pressed, check the inverter connections wit...
  • J
    Jamie TaylorNov 11, 2025
    What to do if the ejector on my Ceia Metal Detector isn't working after an alarm?
    • T
      Timothy ParkNov 11, 2025
      If the ejector on your Ceia Metal Detector isn't activating after an alarm and there's no fault message, here's what you can check: * If the ejector isn't working and there's no ejection confirmation sensor, check the ejector connections. For non-integrated systems, ensure the electrical characteristics are compatible with those provided by the power supply card. If used, check the activation of the EJECT RELAY and its fuse. * If the ejector is working (checked in I/O status) and ejection confirmation check is correctly activated, and you're in synchronized ejection mode, verify the synchronization photocell is activated correctly and operating. If an encoder is installed, check that the speed measured is correct. If no encoder is installed, check that the KE parameter is equal to 0. ...

Summary

Safety Instructions and Warnings

Device User Instruction and Training

Details required instruction levels and training for different user roles throughout the device lifecycle.

General Safety Warnings

General safety precautions and instructions for handling and operating the equipment.

Installation Safety Warnings

Specific safety precautions related to the installation process of the device.

Operational Safety Warnings

Critical safety instructions to follow during the normal use and operation of the device.

Maintenance Safety Warnings

Safety precautions to be observed during maintenance operations.

Permitted Uses and Residual Risks

Defines allowed uses and potential hazards that remain after safety measures.

Product Description

General System Overview

Provides a high-level introduction to the CEIA THS inspection systems.

Detection Probe Models

Details various models of detection probes, their features, and specifications.

Applicable Power Supply Boxes

Describes different power supply box options and their connectivity.

Integrated System Configurations

Outlines available integrated systems with conveyor belts and their variations.

Technical Specifications

Lists detailed technical characteristics and specifications for the metal detector.

Installation and Configuration

Installation Requirements and Guidelines

Covers general requirements, clearances, and guidelines for installing the system.

Unpacking and Handling Procedures

Step-by-step instructions for unpacking and safely handling the equipment.

Mechanical and Electrical Installation

Detailed procedures for the physical and electrical installation of components.

System Configuration Procedures

Guides users through initial setup, preliminary settings, and input/output checks.

Ejection Mode and Timing Settings

Explains how to configure ejection modes and timing parameters for optimal performance.

Device Operation and Use

Optical Indicators

Details the visual indicators on the control panel and external beacon for system status.

Controls Overview

Describes the keys and functions of the control panels for operating the device.

Programming Access and Operation

Guides users on how to enter and perform programming tasks on the Metal Detector.

Startup and Operation Signals

Explains power-on signals, operating status indicators, and display messages.

Operational Procedures: Alarms, Resets, and Speed

Covers handling alarms, faults, starting/stopping belts, and adjusting belt speed.

Sensitivity Check and Test Procedures

Outlines the process for performing sensitivity checks and detailed testing.

Maintenance and Troubleshooting

Periodic Maintenance Schedule

Lists recommended periodic maintenance operations and their frequencies.

Cleaning and Belt Maintenance

Provides instructions for cleaning the conveyor belt and associated components.

Troubleshooting Common Issues

Offers solutions for common problems and fault conditions encountered with the device.

Self-Diagnosis System and Fault Codes

Explains the self-diagnosis system and how to interpret fault messages.

Uninstallation and Disposal Procedures

Details the steps for safely uninstalling and disposing of the device.

Appendices

CE Declaration of Conformity

Official declaration of the product's compliance with European standards.

Spare Parts Information

Guidance on how to identify and order spare parts for the device.

Ceia THS/21E-3F Specifications

General IconGeneral
BrandCeia
ModelTHS/21E-3F
CategoryMetal Detector
LanguageEnglish

Related product manuals