Cessna T188C - Page 156

MODEL
188
&
T188
SERIES
SERVICE
MANUAL
left and
right doors.
c.
TAILWHEEL
STEERING
CABLES.
2.
Remove
access
plate
from tailcone
below
1. Complete
step
2 of
subparagraph
"a."
bellcranks
(15).
2. Disconnect
cables
(13) at
springs
(16).
3. Remove
safety
wire
and relieve
cable
tension
3. Remove
cable
guard
and pulleys
in
Detail
C
at turnbuckles
(7
and
8).
as necessary
to ease
removal
of
cables.
4.
Disconnect
cables
(3 and
9)
at rudder
bar
4.
Disconnect
cables
(13)
at tailwheel
bellcrank
arms
and
at bellcranks
(15).
and
work
cables
out
of tailcone
openings.
5.
Remove
pulleys
and
cable
guards
in Detail
B
5.
Reverse
the
preceding
steps
for
reinstalla-
as
necessary
to
work
cables
free
of aircraft.
tion.
Install
pulleys
and
cable
guards.
Ensure
cables
are
in pulley
grooves
before
installing
guards
and
re-
NOTE
install
all
items
removed
for
access.
To
ease
routing
of
cables,
a
length
of wire
10-11.
RIGGING.
may
be
attached
to
end
of
the
cable
before
a.
Remove
fuselage
access
panels
from
below
left
being
withdrawn
from
aircraft.
Leave
wire
and
right
doors.
in
place,
routed
through
structure;
then
at-
b. Remove
screws
securing
stinger,
disconnect
tach
cable
being
installed
and
pull
the
cable
tail
light
wire
and
remove
stinger
from
aircraft.
into
position.
c.
Disconnect
tailwheel
steering
cables
at tailwheel
bellcrank.
6. Reverse
the
preceding
steps
for
reinstalla-
d.
(See
figure
10-1.)
Remove
safety
wire
and
tion.
relieve
cable
tension
at
turnbuckles
(7
and
8).
7.
After
cables
are
routed
in position,
install
e. Adjust
travel
stop bolts
(18)
to
obtain
degree
of
pulleys
and cable
guards.
Ensure
cables
are
in
travel
specified
in
figure
1-1.
Figure
10-4
illustrates
pulley
grooves
before
installing
guards.
Rig
system
one method
of checking
travel.
in accordance
with paragraph
10-11,
safety turn-
f. (See
figure
10-2.) Adjust
turnbuckles
(index
buckles
and
reinstall
all
items
removed
for access.
7
and
8, figure
10-1)
evenly
so
rudder
pedal
pivot
b. AFT
CABLES.
points
are approximately
5.75 inches
from the
hopper
1. Remove
screws
securing
stinger,
disconnect
while
the
rudder
is offset
1
°
to the
right
(5/16
inch
tail
light
wire
and remove
stinger
from
aircraft.
at lower
trailing
edge
of rudder).
Check
that rudder
2. Complete
steps
1, 2 and
3 of subparagraph
pedals
clear
hopper when
full brake
and
rudder are
"a."
applied
in each
direction.
It
may be
necessary
to
3. Disconnect
cables
(10 and
11)
at bellcranks
rig
them
slightly
farther
than
the
6 inches
specified
(15).
for sufficient
clearance
with
a loaded
hopper.
4.
Disconnect
cables
(10 and
11)
at bellcrank
g.
Safety
turnbuckles,
reconnect
tailwheel
steering
(17).
cables
and
reinstall
all
items
removed
for
access.
5.
Complete
"NOTE'
in
step
5 of
subparagraph
"a." WARNING
6. Reverse
the preceding
steps for
reinstalla-
tion.
Rig
system
in accordance
with
paragraph
10-11,
Be
sure
rudder
moves
in
the
correct
direction
safety
turnbuckles
and
reinstall
all
items
removed
when
operated
by the
rudder
pedals.
for
access.
10-6