Need help?Do you have a question about the CIAT GeoCIAT and is the answer not in the manual?
General| Brand | CIAT |
|---|---|
| Model | GeoCIAT |
| Category | Measuring Instruments |
| Language | English |
Details about the GeoCIATTM Modular's compliance with European directives and standards.
Important safety information and provisions concerning unit handling and operation.
Guidance on proper disposal of the product and its packaging in an environmentally responsible manner.
Table detailing the unit's weight in empty and operational states.
Instructions for selecting and mounting the control terminal and the outdoor sensor.
Installation and mounting instructions for the outdoor sensor.
Guidelines for the proper placement and installation of the heat pump unit itself.
Detailed instructions and diagrams for making the necessary hydraulic connections for the unit.
Instructions for making electrical connections to the unit, including power supply and wiring.
Detailed electrical specifications, including voltage, current, and cable sizing requirements.
Guidance on how to route power and control cables for installation.
Instructions for mounting and removing the unit's control board, including safety precautions.
Essential checks to perform before starting up the unit, such as leak tests and voltage verification.
Procedure for powering up and initializing the control terminal and heat pump.
Step-by-step guide to pair the control terminal with the heat pump unit.
Instructions for pairing the outdoor sensor with the control terminal.
Process for replacing a radio temperature sensor for dual zone management.
Procedure for replacing the HomeConnect control board due to an electronic fault.
Steps to configure machine parameters for optimal system performance.
Instructions for starting the heat pump unit for the first time, considering single-phase and three-phase models.
Information on adjusting the accelerator pump speed and its release screw.
Procedure for bleeding air from the heating circuit, especially important for units installed at high points.
Steps to activate the underfloor heating system, including manual requests if needed.
Procedures for routine maintenance tasks on the unit's components like compressor and pumps.
Guidelines for working on the unit's electrical panel, including tightening torques.
Important information and regulations regarding refrigerant handling and environmental impact.
Mandatory annual checks for the refrigeration circuit, electrical connections, and glycol mix.
Recommendations for users to ensure correct unit operation and maintenance.
Table for recording operating readings and performing annual checks.
Explanation of the graphical display and information areas of the HomeConnect control terminal.
Guide to accessing different access levels and their associated settings on the control terminal.
Details on adjusting machine parameters to suit specific system requirements and optimize performance.
Explanation of adjustment parameters used to fine-tune the machine's operation based on user needs.
Information on accessing and understanding measured and calculated values from sensors and probes.
Explanation of the heat pump's operational counters and product reference information.
Description of different operating modes (Heating, Absence) and how to configure them based on system type.
Configuration and operation of the unit's heating elements and bypass options.
How to control the heat pump and heating elements remotely using on/off inputs.
Detailed technical data for the GeoCIATTM Modular unit, including compressor, heat exchangers, and hydraulic modules.
Information on the sound pressure level of the unit in heating mode.
Minimum and nominal flow rates for the heat exchanger circuits, crucial for preventing freezing.
Schematic diagram illustrating the refrigerating and hydraulic circuits of the unit.
Graphs showing the operating pressure curves for the indoor and outdoor accelerator pumps.
Reference to a table listing fault codes and their descriptions.
Procedure for manually acknowledging and resetting alarms on the unit.
How to access and view stored faults and their associated measurement values.
How the unit automatically restarts after a power outage or stoppage.
Procedure for changing the operating mode of the compressor.
Explanation of the compressor's protection against frequent start-ups.
Description of the self-regulating control function for compressor operation.
Details on the optional pool heating kit and its installation.
Information on the humidity sensor and its function in preventing condensation.
Function of the limiter thermostat in controlling water inlet temperature for underfloor heating.
Description of the optional kit for domestic hot water heating.
Details on the optional CAPA 100L buffer tank module.
Information on the option for controlling two heating zones independently.
Description of the optional 4kW electric heating element kit.
Information on the passive cooling option for home cooling without compressor operation.
Detailed diagram and connection points for the electronic control board.
To Next Page