Cisco 1130AG - Aironet - Wireless Access Point - Page 26

126 pages

To Next Page

To Previous Page

1-12

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

OL-8369-05

Chapter 1 Overview

Network Example with Lightweight Access Points

Main Page

Default Chapter3
- Table of Contents3
- Audience9
- Organization9
Preface9
- Conventions10
- Obtaining Documentation, Obtaining Support, and Security Guidelines12
- Related Publications12
- Locating the Product Serial Number13
Chapter 1 Overview15
- Product Terminology15
- Autonomous Access Points15
- Lightweight Access Points15
- Guidelines for Using 1130AG Series Lightweight Access Points16
- Hardware Features17
- Network Examples with Autonomous Access Points21
- Network Example with Lightweight Access Points25
Installing the Access Point27
Chapter 2 Installing the Acces Point28
Warnings28
Safety Information28
- FCC Safety Compliance Statement28
- General Safety Guidelines28
Unpacking the Access Point29
- Package Contents29
Basic Installation Guidelines30
Controller Discovery Process for Lightweight Access Points30
Deploying the Access Points on the Wireless Network31
- Access Point Layout and Connectors32
- Mounting Plate33
- Suspended Ceiling Adjustable T-Rail Clips34
Opening the Access Point Cover37
Mounting the Access Point on a Horizontal Surface38
Mounting the Access Point below a Suspended Ceiling39
Mounting the Access Point above a Suspended Ceiling40
Mounting Access Point on a Network Cable Box42
Mounting Access Point on a Desktop or Shelf42
Attaching the Access Point to the Mounting Plate42
Securing the Access Point44
- Using a Security Cable44
- Securing the Access Point to the Mounting Plate45
- Connecting the Ethernet and Power Cables47
  - Connecting to an Ethernet Network with an Inline Power Source48
  - Connecting to an Ethernet Network with Local Power49
- Rotating the Cisco Logo50
CHAPTER 3 Troubleshooting Autonomous Access Points3-152
Checking the Autonomous Access Point Leds52
- C H a P T E R 3 Troubleshooting Autonomous Access Points53
Checking Basic Settings54
- Default IP Address Behavior54
- Default SSID and Radio Behavior54
- Enable Radio Interfaces55
- Ssid55
  - WEP Keys55
  - Security Settings56
Low Power Condition for Autonomous Access Points56
- Intelligent Power Management57
  - Inline Power Status Messages57
- Configuring Power Using the CLI60
  - Issuing the Cisco IOS Command Using the CLI61
- Configuring the Access Point System Power Settings Using a Browser62
Running the Carrier Busy Test64
Running the Ping Test65
Resetting to the Default Configuration66
- Using the MODE Button66
- Using the Web Browser Interface66
Reloading the Access Point Image67
- Using the MODE Button67
- Web Browser Interface68
  - Browser HTTP Interface68
  - Browser TFTP Interface69
Obtaining the Access Point Image File69
- Connecting to the Access Point Console Port70
Obtaining the TFTP Server Software71
CHAPTER 4 Troubleshooting Lightweight Access Points74
Guidelines for Using 1130AG Series Lightweight Access Points74
- Using DHCP Option 4374
Checking the Lightweight Access Point Leds74
Low Power Condition for Lightweight Access Points78
- Intelligent Power Management78
- Configuring Power Using Controller CLI Commands79
Manually Configuring Controller Information Using the Access Point CLI80
- Configuring Controller Information81
- Clearing Manually Entered Controller Information81
- Manually Resetting the Access Point to Defaults81
Returning the Access Point to Autonomous Mode81
- Using a WLAN Controller to Return the Access Point to Autonomous Mode82
- Using the MODE Button to Return the Access Point to Autonomous Mode82
- MODE Button Setting83
Obtaining the Autonomous Access Point Image File83
Connecting to the Access Point Console Port84
Obtaining the TFTP Server Software85
Appendix87
Translated Safety Warnings87
Appendix89
Declarations of Conformity and Regulatory Information89
- Manufacturers Federal Communication Commission Declaration of Conformity Statement90
  - VCCI Statement for Japan91
- Industry Canada92
  - Canadian Compliance Statement92
- European Community, Switzerland, Norway, Iceland, and Liechtenstein92
  - Declaration of Conformity with Regard to the 1999/5/EC (R&TTE Directive93
- Declaration of Conformity for RF Exposure95
- Guidelines for Operating Cisco Aironet Access Points in Japan96
  - Japanese Translation96
  - English Translation96
- Administrative Rules for Cisco Aironet Access Points in Taiwan97
  - Access Points with IEEE 802.11A Radios97
    - Chinese Translation97
    - English Translation97
  - All Access Points98
- Declaration of Conformity Statements100
  - Declaration of Conformity Statements for European Union Countries100
  - Declaration of Conformity101
Appendix103
Access Point Specifications103
Appendix107
Channels and Maximum Power Levels107
Appendix109
Console Cable Pinouts109
- Overview109
- Console Port Signals and Pinouts109
Appendix111
Priming Lightweight Access Points Prior to Deployment111
Appendix115
Configuring DHCP Option 43 for Lightweight Access Points115
- Overview116
- Configuring Option 43 for 1000 and 1500 Series Access Points117
- Configuring Option 43 for 1100, 1130, 1200, 1240, and 1300 Series Lightweight Access Points118

Cisco 1130AG - Aironet - Wireless Access Point - Page 26

Table of Contents

Related product manuals