Name: Cisco 1242AG - Aironet - Wireless Access Point
Brand: Cisco
Rating: 4 (1 reviews)

To Next Page

To Previous Page

B-9

Cisco Aironet 1240AG Series Access Point Hardware Installation Guide

OL-8371-05

Appendix B Declarations of Conformity and Regulatory Information

Administrative Rules for Cisco Aironet Access Points in Taiwan

This section provides administrative rules for operating Cisco Aironet access points in Taiwan. The

rules are provided in both Chinese and English.

Access Points with IEEE 802.11a Radios

Chinese Translation

English Translation

This equipment is limited for indoor use.

Default Chapter3
- Table of Contents3
- Audience9
Chapter 2 Installing the Access Point9
- Organization9
Preface9
- Purpose9
- Conventions10
- Related Publications12
- Locating the Product Serial Number13
- Obtaining Documentation, Obtaining Support, and Security Guidelines14
Chapter 1 Overview15
- Product Terminology15
- Autonomous Access Points15
- Lightweight Access Points16
- Guidelines for Using Cisco Aironet Lightweight Access Points16
- Hardware Features17
- Network Examples with Autonomous Access Points22
- Network Example with Lightweight Access Points27
- Chapter 2 Installing the Acces Point30
Safety Information30
- FCC Safety Compliance Statement30
- General Safety Guidelines30
Warnings30
Unpacking the Access Point31
- Package Contents31
Basic Installation Guidelines32
Controller Discovery Process for Lightweight Access Points32
- Deploying the Access Points on the Wireless Network33
  - Access Point Layout and Connectors34
Mounting Overview35
Mounting on a Horizontal or Vertical Surface37
Mounting below a Suspended Ceiling38
Mounting above a Suspended Ceiling39
Mounting Access Point on a Desktop or Shelf42
Cable Security Bracket42
- Removing the Cable Security Bracket43
Attaching the Access Point to the Mounting Plate44
Securing the Access Point45
- Using a Security Cable45
- Securing the Access Point to the Mounting Plate46
Connecting the Ethernet and Power Cables48
- Connecting to an Ethernet Network with an Inline Power Source49
- Connecting to an Ethernet Network with Local Power50
Powering up the Access Point50
- Access Points51
- C H a P T E R 3 Troubleshooting 1240AG Series Autonomous Access Points52
CHAPTER 3 Troubleshooting 1240AG Series Autonomous Access Points52
Checking the Lightweight Access Point Leds52
Checking Basic Settings53
- Default IP Address Behavior54
- Enabling the Radio Interfaces54
- Ssid54
  - WEP Keys55
  - Security Settings55
Low Power Condition55
- Intelligent Power Management56
  - Inline Power Status Messages57
- Configuring Power Using the CLI59
  - Issuing the Cisco IOS Command Using the CLI60
- Configuring the Access Point System Power Settings Using a Browser61
Running the Carrier Busy Test63
Running the Ping Test64
Resetting to the Default Configuration64
- Using the MODE Button65
- Using the Web Browser Interface65
Reloading the Access Point Image66
- Using the MODE Button66
- Web Browser Interface67
  - Browser HTTP Interface67
  - Browser TFTP Interface68
Obtaining the Access Point Image File69
- Connecting to the Access Point Locally70
Obtaining the TFTP Server Software70
- C H a P T E R 4 Troubleshooting 1240AG Series Lightweight Access Points72
- Using DHCP Option 4372
CHAPTER 4 Troubleshooting 1240AG Series Lightweight Access Points72
Guidelines for Using Cisco Aironet Lightweight Access Points72
Checking the Lightweight Access Point Leds73
Low Power Condition for Lightweight Access Points75
- Intelligent Power Management75
- Configuring Power Using Controller CLI Commands76
Manually Configuring Controller Information Using the Access Point CLI77
- Configuring Controller Information78
- Clearing Manually Entered Controller Information78
- Manually Resetting the Access Point to Defaults78
- Returning the Lightweight Access Point to Autonomous Mode79
Obtaining the Autonomous Access Point Image File80
- Connecting to the Access Point Locally81
Obtaining the TFTP Server Software82
Appendix83
Translated Safety Warnings83
Appendix85
Declarations of Conformity and Regulatory Information85
- Manufacturers Federal Communication Commission Declaration of Conformity Statement86
- VCCI Statement for Japan87
  - Canadian Compliance Statement88
Industry Canada88
- Declaration of Conformity with Regard to the 1999/5/EC (R&TTE Directive89
- European Community, Switzerland, Norway, Iceland, and Liechtenstein88
- Declaration of Conformity for RF Exposure91
- Guidelines for Operating Cisco Aironet Access Points in Japan92
  - Japanese Translation92
  - English Translation92
- Administrative Rules for Cisco Aironet Access Points in Taiwan93
  - Access Points with IEEE 802.11A Radios93
    - Chinese Translation93
    - English Translation93
  - All Access Points94
    - Chinese Translation94
    - English Translation94
Operation of Cisco Aironet Access Points in Brazil95
- Declaration of Conformity Statements96
- Declaration of Conformity Statements for European Union Countries96
Appendix101
Access Point Specifications101
Appendix105
Channels and Maximum Power Levels105
Appendix107
Console Cable Pinouts107
- Overview107
- Console Port Signals and Pinouts107
Appendix109
Priming Lightweight Access Points Prior to Deployment109
Appendix113
Configuring DHCP Option 43 for Lightweight Access Points113
- Overview113
- Configuring Option 43 for 1000 Series Access Points113
- Configuring Option 43 for 1100, 1130, 1200, 1240, and 1300 Series Lightweight Access Points116

Cisco 1242AG - Aironet - Wireless Access Point User Manual

Table of Contents

Questions and Answers:

Cisco 1242AG - Aironet - Wireless Access Point Specifications

Related product manuals

Brand	Cisco
Model	1242AG - Aironet - Wireless Access Point
Category	Wireless Access Point
Language	English