EasyManuals Logo

Cisco 3750G - Catalyst Integrated Wireless LAN Controller User Manual

Cisco 3750G - Catalyst Integrated Wireless LAN Controller
1204 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #922 background imageLoading...
Page #922 background image
36-12
Catalyst 3750 Switch Software Configuration Guide
OL-8550-02
Chapter 36 Configuring IPv6 Unicast Routing
Configuring IPv6
Beginning in privileged EXEC mode, follow these steps to assign an IPv6 address to a Layer 3 interface
and enable IPv6 routing:
Command Purpose
Step 1
configure terminal Enter global configuration mode.
Step 2
sdm prefer dual-ipv4-and-ipv6 {default |
routing | vlan} [desktop]
Select an SDM template that supports IPv4 and IPv6.
• default—Set the switch to the default template to balance
system resources.
• routing—Set the switch to the routing template to support
IPv4 and IPv6 routing, including IPv4 policy-based routing.
• vlan—Maximize VLAN configuration on the switch with
no routing supported in hardware.
• desktop—Supported only on Catalyst 3750-12S aggregator
switches to set the switch to one of the desktop templates. If
not selected on an aggregator switch, an aggregator template
is automatically selected.
Step 3
end Return to privileged EXEC mode.
Step 4
reload Reload the operating system.
Step 5
configure terminal Enter global configuration mode (after the switch has reloaded).
Step 6
interface interface-id Enter interface configuration mode, and specify the Layer 3
interface to configure. The interface can be a physical interface,
a switch virtual interface (SVI), or a Layer 3 EtherChannel.
Step 7
no switchport Remove the interface from Layer 2 configuration mode (if it is a
physical interface).
Step 8
ipv6 address ipv6-prefix/prefix length eui-64
or
ipv6 address ipv6-address link-local
or
ipv6 enable
Specify a global IPv6 address with an extended universal
identifier (EUI) in the low-order 64 bits of the IPv6 address.
Specify only the network prefix; the last 64 bits are
automatically computed from the switch MAC address. This
enables IPv6 processing on the interface.
Specify a link-local address on the interface to be used instead
of the link-local address that is automatically configured when
IPv6 is enabled on the interface. This command enables IPv6
processing on the interface.
Automatically configure an IPv6 link-local address on the
interface, and enable the interface for IPv6 processing. The
link-local address can only be used to communicate with nodes
on the same link.
Step 9
exit Return to global configuration mode.
Step 10
ip routing Enable IP routing on the switch.
Step 11
ipv6 unicast-routing Enable forwarding of IPv6 unicast data packets.
Step 12
end Return to privileged EXEC mode.
Step 13
show ip v6 interface interface-id Verify your entries.
Step 14
copy running-config startup-config (Optional) Save your entries in the configuration file.

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco 3750G - Catalyst Integrated Wireless LAN Controller and is the answer not in the manual?

Cisco 3750G - Catalyst Integrated Wireless LAN Controller Specifications

General IconGeneral
Switching Capacity32 Gbps
RAM128 MB
Flash Memory32 MB
Power DeviceInternal power supply
Ports48 x 10/100/1000 + 4 x SFP
Performance38.7 Mpps
Wireless LAN Controller Capacity50
StackingYes
FeaturesVLAN support, QoS
Compliant StandardsIEEE 802.3, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3z
Operating Humidity10% to 85% non-condensing
Power over Ethernet (PoE)Yes (optional)

Related product manuals