25-5
Cisco Nexus 1000V Troubleshooting Guide, Release 5.2(1)SV3(1.1)
OL-31593-01
Chapter 25 VXLANs
Information About VXLANs
*>i[3]:[5000]:[4]:[192.168.69.104]/88 #VTEP 192.168.69.104 that are learned from peer
172.23.181.68
172.23.181.68 100 0 i
This example shows how to display the detailed output for a specific segment ID or RD:
vsm# show bgp l2vpn evpn rd 172.23.181.67:5000
BGP routing table information for VRF default, address family L2VPN EVPN
BGP table version is 10, local router ID is 172.23.181.67
Status: s-suppressed, x-deleted, S-stale, d-dampened, h-history, *-valid, >-best
Path type: i-internal, e-external, c-confed, l-local, a-aggregate, r-redist
Origin codes: i - IGP, e - EGP, ? - incomplete, | - multipath
Network Next Hop Metric LocPrf Weight Path
Route Distinguisher: 172.23.181.67:5000 (EVI 5000)
BGP routing table entry for [3]:[5000]:[4]:[192.168.69.3]/88, version 4
Paths: (1 available, best #1)
Flags: (0x00000a) on xmit-list, is not in l2rib/evpn
Path type: local, path is valid, is best path
AS-Path: NONE, path locally originated
0.0.0.0 (metric 0) from 0.0.0.0 (0.0.0.0)
Origin IGP, MED not set, localpref 100, weight 32768
Extcommunity:
RT:1:5000
Advertised to peers:
172.23.181.68
BGP routing table entry for [3]:[5000]:[4]:[192.168.69.104]/88, version 10
Paths: (1 available, best #1)
Flags: (0x00001a) on xmit-list, is in l2rib/evpn
Path type: internal, path is valid, is best path
Imported from 172.23.181.68:5000:[3]:[5000]:[4]:[192.168.69.104]/88
AS-Path: NONE, path sourced internal to AS
172.23.181.68 (metric 0) from 172.23.181.68 (172.23.181.68)
Origin IGP, MED not set, localpref 100, weight 0
Extcommunity:
RT:1:5000
Not advertised to any peer
This example shows how to display the BGP convergence time:
switch3# show bgp convergence
Global settings:
BGP start time 00:01:06
Config processing completed 00:00:08 after start
BGP out of wait mode 00:00:30 after start
Information for VRF default
Initial-bestpath timeout: 300 sec, configured 0 sec
First peer up 00:00:29 after start
Bestpath timer not running
IPv4 Unicast:
First bestpath signalled 00:00:08 after start
First bestpath completed 00:00:08 after start
L2VPN EVPN:
First bestpath signalled 00:00:30 after start
First bestpath completed 00:00:30 after start
</>
This example shows how to display the VTEP list for a specific VXLAN segment ID or all segments:
vsm# show bgp l2vpn evpn evi all VTEP
BGP routing table information for VRF default, address family L2VPN EVPN
BGP table version is 17, local router ID is 192.168.66.10
Status: s-suppressed, x-deleted, S-stale, d-dampened, h-history, *-valid, >-best
To Next Page
Loading...
