ComAp IM-NT-BB - Page 83

To Next Page

To Previous Page

InteliMains

, SW version 3.0

InteliMains-NT-BTB-3.0-Reference Guide.pdf, ©ComAp – June 2013

Reaction of the controller on BTB opening externally

BTB fail

BTB fdk

Synchro

BTB UV Coil

BTB OFF Coil

BTB ON Coil

BTB Close/Open

Breaker opened externally, BusR & BusL OK, Sychro succesful

Sync fail

BTB fdk

Synchro

BTB UV Coil

BTB OFF Coil

BTB ON Coil

BTB Close/Open

Breaker opened externally, BusR & BusL OK, Synchro unsuccesful

BTB fail

BTB fdk

Synchro

BTB UV Coil

BTB OFF Coil

BTB ON Coil

BTB Close/Open

Breaker opened externally, one Bus only OK, DeadBusClosing causes breaker to try closing

Main Page

Document Information6
Clarification of Notation7
System Overview8
Configurability and Monitoring9
Winscope10
Installation11
IM-NT Installation Instructions12
Terminal Diagram, Dimensions13
Package Contents14
Mounting15
Terminal Diagram, Dimensions17
Package Contents18
Grounding (General)19
Voltage and Current Inputs20
Binary Input Wiring (General)21
IM-NT-BB and IM-NTC-BB22
Analog Input and Output Wiring23
CAN and RS485 Bus Wiring25
Wiring Examples26
Extension Modules (General)27
Putting It into Operation28
Modem Connection29
Internet Connection30
Airgate Connection31
Connection to Multiple Controllers32
Modification of Configuration, Setpoints Etc33
Programming of a Controller34
Changing the Language37
Password Management38
Access Group Setting in Genconfig39
Related Tools41
Operator Guide42
Firmware and Archives43
Function Description44
Modes52
Process Limitation53
Power Management54
Remote Alarm Messaging55
Example of Setting56
Controller Redundancy57
Force Value – Step by Step Guide58
Regulation Loops59
PI Regulation Adjustment60
Values for Continuous Writing from External Sources61
History Related Functions63
Summer Time Mode64
Virtual Peripheral Inputs-Outputs (VPIO) Module65
Shared Inputs and Outputs66
Distributed Binary Inputs and Outputs67
Modbus Reading and Writing68
Analog Input Sensors and User Sensors69
Languages and Translator Tool in Genconfig70
PLC Functions71
Protections and Alarm Management72
Protection Types73
Bus Left Voltage and Frequency Protections - Limits and Indications74
Reset Actual Alarms Selection77
Peripheral Modules Error Detection78
Circuit Breakers Operation Sequence, MGCB/MCB Fail Detection79
Following Graphs Depict Possible CB Sequences80
Follow Function for Breaker Control in AUT Mode84
Controller Operation States85
Appendix86
List of Objects87
Setpoints - Comprotsetting88
Setpoints - Busr Protect89
Setpoints - Sync Ctrl90
Setpoints - Load Shedding91
Values – List92
Values Group - Gen-Sets93
Values Group - Load Shedding94
Values Group - Statistics95
Binary Output Functions – List96
Breaker Control97
Power Management98
Setpoints99
Group: Basic Settings109
Group: Comms Settings122
Group: Comprotsetting137
Group: Analog Protect139
Group: Busl Protect140
Group: Busr Protect148
Group: Pwr Management152
Group: Sync Ctrl170
Group: Volt Ctrl175
Group: Force Value176
Group: Load Shedding189
Group: Timer Settings191
Group: Act. Calls/Sms196
Group: Date/Time202
Values205
Group: Busr Values214
Group: Gen-Sets Values217
Group: Control Loops226
Group: Force Value229
Group: Load Shedding231
Group: bin Inputs CU233
Group: Log Bout234
Group: Info237
Group: Statistics245
Binary Input Functions249
Table of Binary Input Functions250
Binary Output Functions289
Table of Binary Output Functions290
Analog Input Functions322
Table of Analog Input Functions323
User Notes326

ComAp IM-NT-BB - Page 83

Table of Contents

Related product manuals