Atena Easy Addressable Fire Alarm Panel – Installation and Programming Manual
2
Table of Contents
1. INTRODUCTION ........................................................................................................................................................... 4
1.1. General Description ....................................................................................................................................... 4
1.2. General Specifications ................................................................................................................................... 4
1.2.1 General Technical Specifications ................................................................................................... 4
1.2.2 Possible Hardware Configurations ................................................................................................. 5
1.2.3 Environment .................................................................................................................................... 5
1.2.4 Electrical Characteristics ................................................................................................................ 5
2. INSTALLATION............................................................................................................................................................. 7
2.1. Wall Mounting ................................................................................................................................................ 7
2.2. System Components ..................................................................................................................................... 8
2.2.1 Front panel ...................................................................................................................................... 8
2.2.2 Configuration of the basic modules .............................................................................................. 10
2.2.3 Description of the main PCB (control panel) ................................................................................ 10
2.3. Connection of Signaling Devices ................................................................................................................. 12
2.3.1 Connecting of Sounders ............................................................................................................... 12
2.3.2 Connecting of Signaling Devices .................................................................................................. 12
2.3.3 Connecting to the Specialized Inputs ........................................................................................... 12
2.3.4 Loop Controller ............................................................................................................................. 13
2.4. Connecting to the Main Power Source ........................................................................................................ 14
2.5. Connecting the Accumulator Battery ........................................................................................................... 14
2.6. Connecting a Heat Printer ........................................................................................................................... 15
2.7. Connecting a Network Module..................................................................................................................... 15
3. PROGRAMMING TYPES ............................................................................................................................................ 16
3.1. Programming via AtenaProg Software ........................................................................................................ 16
3.2. Programming via Panel’s Keyboard ............................................................................................................ 16
3.3. Firmware Update ......................................................................................................................................... 16
3.3.1 Firmware Update from Computer ................................................................................................. 16
3.3.2 Firmware Update from USB Drive ................................................................................................ 17
3.3.3 Copying Image File from the Panel to USB Drive ........................................................................ 17
4. FULL HARDWARE RESET ........................................................................................................................................ 17
5. PROGRAMMING OF ATENA EASY FIRE ALARM PANEL ...................................................................................... 18
5.1. General Information for Programming and Operation ................................................................................. 18
5.2. Codes and Access Levels ........................................................................................................................... 18
6. DESCRIPTION OF THE OPERATION MODES ......................................................................................................... 20
6.1. Review of Alarm Events ............................................................................................................................... 20
6.2. Review of Fault Events ................................................................................................................................ 20
6.3. Review of Disablements .............................................................................................................................. 21
6.4. Review of Running Tests ............................................................................................................................. 21
6.5. Review of Warning Messages ..................................................................................................................... 22
6.6. Silencing the Internal Buzzer ....................................................................................................................... 23
6.7. Silencing the Sounders ................................................................................................................................ 23
6.8. Activate Evacuation ..................................................................................................................................... 23
6.9. Resetting the Panel ..................................................................................................................................... 23
6.10. Indication Test ........................................................................................................................................... 23
7. DESCRIPTION OF THE PROGRAMMING MENUS ................................................................................................... 24
7.1. View History Log Menu ................................................................................................................................ 24
7.1.1 Review of Full Events List ............................................................................................................ 24
7.1.2 Review of List of Events by Date .................................................................................................. 25
7.1.3 Deleting the Events in the LOG file .............................................................................................. 25
7.1.4 Printing Events .............................................................................................................................. 25
7.1.5 Printer Settings ............................................................................................................................. 25
7.2. Zones Menu ................................................................................................................................................. 26
7.2.1 General Submenus ....................................................................................................................... 26
7.2.2 Zones Testing ............................................................................................................................... 26
7.2.3 Disabling Zones ............................................................................................................................ 27
7.2.4 Programming Zone Parameters ................................................................................................... 27
7.2.5 Zone Name ................................................................................................................................... 27
7.2.6 Zone Operation Modes ................................................................................................................. 27
7.2.7 Programming Delays Т2 ............................................................................................................... 28
7.2.8 Arranging Zones in Groups .......................................................................................................... 29
7.3. Devices Setup Menus .................................................................................................................................. 29
7.3.1 Submenus for General Setting ..................................................................................................... 29
To Next Page
Loading...
