Creative Blaster User Manual (English)

Other manuals for Creative Blaster

Questions and Answers:

P
Paul AlvaradoAug 17, 2025
What to do if there is no audio output when playing .WAV, MIDI, or AVI files on my Creative Sound Card?
- M
  Michael ParksAug 17, 2025
  If you're not getting any sound when playing digital files, there are several things to check: * Ensure that the speaker volume knob (if your speakers have one) is set to a mid-range level. * Use Creative Mixer to adjust the volume if needed. * Verify that your powered speakers or external amplifier are connected to the sound card's Line Out or Rear Out jack. * Confirm there is no hardware conflict between the sound card and any other peripheral device. See 'Resolving' for conflict resolution. * Make sure the output selection in the Speaker applet's Configuration tab corresponds to your speaker or headphone configuration. * Ensure the Original Sound sliders in both the Master and Source tabs of the Environmental Audio applet are set to 100%.
S
smithsusanAug 19, 2025
How to fix no audio output when playing CD-Audio on Creative Sound Card?
- J
  Jennifer RamirezAug 20, 2025
  If you're not getting any sound when playing CD-Audio, ensure that the CD audio cable is connected between the CD-ROM drive and the sound card. Also, in Creative Mixer’s Play Control view, make sure the check box of the source being played is unmuted (enabled). In the Record Control view, make sure the corresponding check box is also selected.
T
twallaceAug 22, 2025
How to troubleshoot no sound from headphones with Creative Sound Card?
- W
  Wendy WrightAug 23, 2025
  If you're not getting any sound from your headphones, check that the headphones are connected to the Line Out jack. Also, in the Speaker applet, ensure the Output field is set to Headphones.
F
fernandoharrisAug 26, 2025
What to do if rear speakers have no sound on Creative Sound Card?
- S
  sleblancAug 26, 2025
  If you are not getting sound from the rear speakers in a 4-speaker configuration, verify that the rear speakers are connected to the main card’s Rear Out jack. Also, in Creative Mixer’s Record Control view, if a single source (e.g., CD Audio, Line In, TAD, Auxiliary or Microphone) is playing, ensure the check box for that source is selected.
V
Victoria WolfeAug 28, 2025
Why is my Creative Sound Card joystick not working properly in some programs?
- M
  Matthew BowmanAug 28, 2025
  If the joystick isn't working correctly in some programs, the program might be using the system processor timing to calculate the joystick position. Try increasing your system's 8 bit I/O recovery time in the BIOS settings, usually found under the Chipset Feature Settings section.
C
Carlos CarsonAug 31, 2025
Why is there excessive environmental sound with my Creative Sound Card?
- B
  brenda01Aug 31, 2025
  If you hear too much environmental sound or effects when playing audio, it might be because an inappropriate environmental preset is selected. To fix this, open the Environmental Audio control applet or display Creative Launcher (at the top or bottom of your screen). Click the Environments tab and select 'No effects' or a more suitable environment from the list.
J
james98Sep 2, 2025
What to do if there is insufficient memory to load SoundFonts on Creative Sound Card?
- L
  Lynn CarrSep 2, 2025
  If you're getting an error about insufficient memory to load SoundFonts, try the following: * In the SoundFont Control applet, go to the Options tab and move the SoundFont Cache slider to the right to allocate more memory. * Alternatively, go to the Configure Banks tab in the SoundFont Control applet and select a smaller SoundFont bank from the Select Bank box.
K
Kristi MercadoSep 5, 2025
Why doesn't the Creative Sound Card installation program run automatically in Windows 95/98?
- Z
  Zachary OrrSep 5, 2025
  If the installation program doesn't start automatically in Windows 95/98 after inserting the CD-ROM, it could be that the AutoPlay feature is disabled. To start the installation manually, double-click the My Computer icon, right-click the CD-ROM drive icon, and select AutoPlay. Follow the on-screen instructions. To enable AutoPlay, go to Control Panel, double-click the System icon, go to Device Manager, select your CD-ROM drive, click Properties, go to the Settings tab, and ensure the Auto Insert Notification check box is selected.
D
Donald MoonSep 8, 2025
How to fix Service Control Manager error after removing Creative Sound Blaster Live! card?
- U
  uvaughnSep 8, 2025
  If you receive a Service Control Manager error message after removing a Sound Blaster Live! card, log on as Administrator. Go to Control Panel, double-click the Multimedia icon, and click the Devices tab. Remove all items except 'Audio for Creative SB Live!', 'MIDI for Creative SB Live!', and 'MIDI for Creative S/W Synth' from under Audio Devices and MIDI Devices And Instruments.
T
Thomas HurleySep 12, 2025
What to do if Creative Sound Card causes system to freeze during voice output?
- J
  jared61Sep 12, 2025
  If the system stops responding during voice output, there might be a conflict between the sound card and another card. Resolve this as you would for Windows 95/98, using the instructions in the previous section.