EasyManua.ls Logo

CUH SDVC31 Series - On;Off Delay of Intelligent Photoelectric Sensor

CUH SDVC31 Series
48 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
CUH CUH CUH CUH CUH CUH CUH
CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH
CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH
CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH
CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH
CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH
CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH
CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH
CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH CUH
13
When using a sensors or PLC to turn on or turn off the controller's main output,
the action can be delayed for a period of time after the control signal is given
or restored. The delay time can be set through the two parameters below.
Variable Frequency Digital Controller
for Vibr
atory Feeder
Saturated Accelerate
Remote
Stop
Lock
Voltage
Frequency
On Delay
Off Delay
Soft Start
SDVC31-M
Variable Frequency Digital Controller
for Vibr
atory Feeder
Saturated Accelerate
Remote
Stop
Lock
Voltage
Frequency
On Delay
Off Delay
Soft Start
SDVC31-M
4.3 On/Off Delay of Intelligent Photoelectric Sensor
On Delay ( J ): The period of time the controller goes through from receiving
a startup control signal to actually outputting.
Off Delay ( L ): The period of time the controller goes through from receiving
a shutdown control signal to actually cutting off output.
8
to enter the basic parameter
interface.
8Short press to switch to on
delay parameter "J" and the
default value 0.2.
8Pressorto adjust the
parameter value.
Press and hold for 2 seconds
8
to enter the basic parameter
interface.
8Short press to switch to off
delay parameter "L" and the
default value 0.2.
8Pressorto adjust the
parameter value.
Press and hold for 2 seconds
J means
Photoelectric Sensor
On Delay of Intelligent
On Delay Indicator
L means
Photoelectric Sensor
Off Delay of Intelligent
Off Delay Indicator
SDVC31 Series
Variable Frequency Digital Controller for Vibratory Feeder
SDVC31SMSEN_4.012023-08

Related product manuals