How to fix CUH Controller when there is no display after powering on?
If your CUH Controller's display doesn't turn on after you power it on, ensure that the power outlet is working and that the input power cable is securely connected to the outlet.
What to do if CUH Controller display is normal, but there is no output?
If the CUH Controller display is normal but there's no output, verify that the output cable is securely connected to the vibrator. Also, ensure the output voltage isn't too low and the Stop Indicator is not lit. Check if the 'Normal Close' parameter has been set, as this can halt the controller's output.
What to do if CUH Controller shows 'Over Current'?
If your CUH Controller indicates an 'Over Current' error, reduce the output voltage appropriately and then restart the output.
Why is the control signal losing effectiveness in my CUH Controller?
If the control signal is losing effectiveness in your CUH Controller, ensure that the control signal is correctly inputted and the ground wire of the control signal is properly connected to the controller. Also, verify that the Logical Relation of the control signals is set correctly.
What causes abnormal 24V power output on a CUH Controller?
An abnormal 24V power output on your CUH Controller may be due to a short-circuit in the 24V port or the current exceeding 400mA. Ensure the 24V port is not short-circuited and the current does not exceed 400mA.
How to prevent CUH Controller from overheating?
To prevent your CUH Controller from overheating, install it in a well-ventilated environment.
What to do for CUH Controller's 'Over Current protection of Port D'?
If your CUH Controller shows 'Over Current protection of Port D', ensure the load of Port D is not short-circuited and the current doesn't exceed 400mA. Then, try restarting the output of Port D.
Why is the 5V power output of Port A abnormal on my CUH Controller?
If the 5V power output of Port A is abnormal on your CUH Controller, make sure the 5V power of Port A is not short-circuited or connected to an external power voltage exceeding 5V.
How do I resolve 'Beat phenomena' with CUH Controller?
To resolve 'Beat phenomena' with your CUH Controller, avoid vibration coupling among the vibrators and heighten the resonant frequency of the vibrators.
What causes a motor stall fault on a CUH Controller and how to fix it?
A motor stall fault on your CUH Controller may occur if the motor is overloaded or locked. Also, it can happen if the actual speed of the motor is lower than the set minimum speed value. Ensure the motor is not overloaded or locked, and that the actual speed of the motor is not lower than the set minimum speed value.
Verify the controller and accessories are intact upon receipt. Contact the company if any issues are found.
Notes for ensuring better performance and longer lifetime, focusing on ventilation and environmental conditions.
Verify the controller and accessories are intact upon receipt. Contact the company if any issues are found.
Overview of the SDMC20-S controller's capabilities, including soft start, speed stabilization, and protection functions.
Specifies the necessary environmental and electrical conditions for safe and proper controller installation and operation.
Details how to use the controller's buttons in both modern and traditional parameter interfaces.
Explains how to set the output voltage or speed using the controller's interface and buttons.
Details how to control the motor speed using external analog signals like potentiometers or voltage/current inputs.
Explains the connection and configuration of intelligent photoelectric sensors for detection purposes.
Describes the support for NPN, PNP, Ut1, and Ut0 modes for switch sensor connections.
Illustrates the wiring configurations for NPN and PNP/push-pull output types for control signals.
Explains the available signal sources and logic diagrams for controlling the main and control outputs.
Describes the two control output modes: delay mode and hold mode, with timing diagrams.
Explains how the main output signal is controlled, similar to control output, using logic operations and on/off signals.
Details how to use external control signals to select preset motor speeds for multi-speed control systems.
Provides instructions on how to change the motor's rotation direction by adjusting the output connector position.
Explains the motor stall protection feature, how it triggers (Err22), and how to resume operation.
Describes how to view various operating parameters for monitoring and debugging purposes.
Details how to lock key parameters using a password to prevent misoperation and unauthorized changes.
Explains how to connect the controller to a vibratory feeder and set it for feeder control mode.
Instructions on how to restore factory settings to use the traditional SDVC21-S interface for feeder control.
A comprehensive table listing all controller parameters, their symbols, ranges, and default values.
Diagrams illustrating the electrical connections for various input and output ports of the controller.
Provides common error codes and their corresponding troubleshooting methods for diagnosing issues.
Provides detailed physical dimensions of the controller unit in millimeters.
Lists the electrical and performance specifications of the controller, including voltage, current, and frequency.
Details the GB and IEC standards the controller complies with for electrostatic discharge and immunity.
Specifies the warranty duration for the product, which is 3 years from the date of delivery.
Outlines the conditions and exclusions for product warranty coverage.
Defines the intended applications and industries for the controller and those it is not suitable for.
General| Category | Controller |
|---|---|
| Motion Sensor | Six-axis motion sensing system (three-axis gyroscope, three-axis accelerometer) |
| Light Bar | Yes |
| Speaker | Built-in mono speaker |
| Model | SDMC20-S |
| Connection | Bluetooth, USB |
| Battery | Lithium-Ion Rechargeable Battery |
| Buttons | Directional buttons, Action buttons (Triangle, Circle, Cross, Square), Shoulder buttons (R1/L1), Triggers (R2/L2), Options button, PS button, Touch Pad button |
| Touch Pad | Yes |
| Vibration | Yes |
| Headset Jack | 3.5mm |
| Compatible Platform | PlayStation 4 |
To Next Page
