CULLMANN CUlight FR 60C - Page 29

73
2
Slave Unit Setting
• Set the other camera ash
as the wireless slave Unit.
• As a slave unit, CUlight FR
60C can receive wireless
signals of Canon speedlites
e.g. 580EXII, 600EX-RT
and commanders of Canon
cameras e.g. 7D/60D/600D.
3
Check the communication
channel.
• If the master unit and slave
unit(s) are set to a different
channel, set them to the
same channel. (Page 64)
4
Position the camera and
ashes.
• Position the camera and
ashes as the picture
shows. (Page 61)
5
Set the master unit’s ash
mode to <ETTL>.
• Set the master unit’s ash
mode to < ETTL >.
• For shooting, < ETTL > will
automatically be set for the
slave unit.
• Set the master unit ash
ring as ON to re a ash.
6
Check that the ash is
ready.
• Check that the master ash
ready indicator is lightened.
• When the slave ash ready
indicator is ready, the
AF- assist beam lighting
area will blinks at 1 second
intervals.
7
Check the ash operation.
• Press the master unit’s Test
Button < >.
• Then, the slave unit will re.
If not, adjust the slave unit’s
angle toward the master
unit and distance from the
master unit.
MENU2
2. Master Unit’s Flash OFF
When the master unit is set to OFF, only the slave units will fire a
flash.
Press Function Button 4 so
1 that < > is displayed
on the LCD panel.
Press Function Button 1
2 < > to control the
ON/OFF of the master unit.
< >：The master unit flash
firing is ON.
< >：The master unit flash
firing is OFF.
Even if the master unit flash firing is disabled, it still fires a
preflash to transmit wireless signals.
3. Setting the Communication Channel
If there are other wireless flash systems nearby, you can change the
channel IDs to prevent signal interference. The channel IDs of the
master unit and the slave unit(s) must be set to the same.
Press Function Button 4 so
1 that < > is displayed
on the LCD panel.
Press Function Button 1 so
2 that < > is displayed
on the LCD panel. Turn the
Select Dial to choose a
channel ID from 1 to 4.
Press the <SET> button to
3 confirm.
4. ETTL：Fully Automatic Wireless Flash Shooting
Using Automatic Wireless Flash with a Single Slave Unit
Master Unit Setting
1
● Attach a TT685C camera
flash on the camera and
set it as the master unit.
●As a master unit, TT685C
can control Canon
speedlites e.g. 580EXII,
600EX-RT via wireless.
Slave Unit Setting
2
● Set the other camera flash
as the wireless slave Unit.
● As a slave unit, TT685C
can receive wireless signals
of Canon speedlites e.g.
580EXII, 600EX-RT and
commanders of Canon
cameras e.g. 7D/60D/600D.
Check the communication
3 channel.
● If the master unit and slave
unit(s) are set to a different
channel, set them to the
same channel. (Page 65)
Position the camera and
4 flashes.
● Position the camera and
flashes as the picture
shows. (Page 64)
MENU3
CH
ON/OFF
Set the master unit’s flash
5 mode to <ETTL>.
● Set the master unit’s flash
mode to <ETTL>.
● For shooting, <ETTL> will
automatically be set for the
slave unit.
● Set the master unit flash
firing as ON to fire a flash.
Check that the flash is
6 ready.
● Check that the master flash
ready indicator is lightened.
● When the slave flash ready
indicator is ready, the AF-
assist beam lighting area
will blinks at 1 second
intervals.
Check the flash operation.
7
● Press the master unit’s
Test Button < >.
● Then, the slave unit will
fire. If not, adjust the slave
unit’s angle toward the
master unit and distance
from the master unit.
- 65 - - 66 -
MENU2
2. Master Unit’s Flash OFF
When the master unit is set to OFF, only the slave units will fire a
flash.
Press Function Button 4 so
1 that < > is displayed
on the LCD panel.
Press Function Button 1
2 < > to control the
ON/OFF of the master unit.
< >：The master unit flash
firing is ON.
< >：The master unit flash
firing is OFF.
Even if the master unit flash firing is disabled, it still fires a
preflash to transmit wireless signals.
3. Setting the Communication Channel
If there are other wireless flash systems nearby, you can change the
channel IDs to prevent signal interference. The channel IDs of the
master unit and the slave unit(s) must be set to the same.
Press Function Button 4 so
1 that < > is displayed
on the LCD panel.
Press Function Button 1 so
2 that < > is displayed
on the LCD panel. Turn the
Select Dial to choose a
channel ID from 1 to 4.
Press the <SET> button to
3 confirm.
4. ETTL：Fully Automatic Wireless Flash Shooting
Using Automatic Wireless Flash with a Single Slave Unit
Master Unit Setting
1
● Attach a TT685C camera
flash on the camera and
set it as the master unit.
●As a master unit, TT685C
can control Canon
speedlites e.g. 580EXII,
600EX-RT via wireless.
Slave Unit Setting
2
● Set the other camera flash
as the wireless slave Unit.
● As a slave unit, TT685C
can receive wireless signals
of Canon speedlites e.g.
580EXII, 600EX-RT and
commanders of Canon
cameras e.g. 7D/60D/600D.
Check the communication
3 channel.
● If the master unit and slave
unit(s) are set to a different
channel, set them to the
same channel. (Page 65)
Position the camera and
4 flashes.
● Position the camera and
flashes as the picture
shows. (Page 64)
MENU3
CH
ON/OFF
Set the master unit’s flash
5 mode to <ETTL>.
● Set the master unit’s flash
mode to <ETTL>.
● For shooting, <ETTL> will
automatically be set for the
slave unit.
● Set the master unit flash
firing as ON to fire a flash.
Check that the flash is
6 ready.
● Check that the master flash
ready indicator is lightened.
● When the slave flash ready
indicator is ready, the AF-
assist beam lighting area
will blinks at 1 second
intervals.
Check the flash operation.
7
● Press the master unit’s
Test Button < >.
● Then, the slave unit will
fire. If not, adjust the slave
unit’s angle toward the
master unit and distance
from the master unit.
- 65 - - 66 -
MENU2
2. Master Unit’s Flash OFF
When the master unit is set to OFF, only the slave units will fire a
flash.
Press Function Button 4 so
1 that < > is displayed
on the LCD panel.
Press Function Button 1
2 < > to control the
ON/OFF of the master unit.
< >：The master unit flash
firing is ON.
< >：The master unit flash
firing is OFF.
Even if the master unit flash firing is disabled, it still fires a
preflash to transmit wireless signals.
3. Setting the Communication Channel
If there are other wireless flash systems nearby, you can change the
channel IDs to prevent signal interference. The channel IDs of the
master unit and the slave unit(s) must be set to the same.
Press Function Button 4 so
1 that < > is displayed
on the LCD panel.
Press Function Button 1 so
2 that < > is displayed
on the LCD panel. Turn the
Select Dial to choose a
channel ID from 1 to 4.
Press the <SET> button to
3 confirm.
4. ETTL：Fully Automatic Wireless Flash Shooting
Using Automatic Wireless Flash with a Single Slave Unit
Master Unit Setting
1
● Attach a TT685C camera
flash on the camera and
set it as the master unit.
●As a master unit, TT685C
can control Canon
speedlites e.g. 580EXII,
600EX-RT via wireless.
Slave Unit Setting
2
● Set the other camera flash
as the wireless slave Unit.
● As a slave unit, TT685C
can receive wireless signals
of Canon speedlites e.g.
580EXII, 600EX-RT and
commanders of Canon
cameras e.g. 7D/60D/600D.
Check the communication
3 channel.
● If the master unit and slave
unit(s) are set to a different
channel, set them to the
same channel. (Page 65)
Position the camera and
4 flashes.
● Position the camera and
flashes as the picture
shows. (Page 64)
MENU3
CH
ON/OFF
Set the master unit’s flash
5 mode to <ETTL>.
● Set the master unit’s flash
mode to <ETTL>.
● For shooting, <ETTL> will
automatically be set for the
slave unit.
● Set the master unit flash
firing as ON to fire a flash.
Check that the flash is
6 ready.
● Check that the master flash
ready indicator is lightened.
● When the slave flash ready
indicator is ready, the AF-
assist beam lighting area
will blinks at 1 second
intervals.
Check the flash operation.
7
● Press the master unit’s
Test Button < >.
● Then, the slave unit will
fire. If not, adjust the slave
unit’s angle toward the
master unit and distance
from the master unit.
- 65 - - 66 -
R
616x0_CUlight_FR60X_BDA_Canon englisch.indd 73 24.10.2016 13:56:22